Siemens SIMATIC IPC627E Operating Instructions Manual Download

Page: 67 / 164

Operating the device

5.5 Remote maintenance of the device

SIMATIC IPC627E
Operating Instructions, 12/2018, A5E44297201-AA

5.5

Remote maintenance of the device

5.5.1

Remote maintenance functions

Remote maintenance of the devices is performed using Intel® Active Management

Technology (iAMT), which is integrated in the hardware and firmware of the computer, and

the SIMATIC IPC Remote Manager software.
By using remote access to SIMATIC IPCs, system or program errors can be corrected from

a control room (without on-site presence), for example, and program updates and

firmware/BIOS settings can be performed. Access is possible even if the operating system

no longer starts.
Some examples of iAMT's remote maintenance functions are listed below:

Function

Description

Remote control

(keyboard / video / mouse

redirection)

With KVM redirection, you can operate SIMATIC IPCs remotely,

even if they have no operating system or the operating system is

corrupt.
A KVM remote session is always possible with the KVM server inte-

grated in the firmware. This allows you to restart the IPC and change

firmware/BIOS settings remotely.

Remote Power Management SIMATIC IPCs can be turned on and off and restarted from another

PC.

IDE redirection

An ISO file on the Help Desk PC can be integrated and used on the

SIMATIC IPC as a DVD drive.
An ISO file contains a memory image of the content of a CD or DVD

structured in the ISO 9660 format.

Remotes Booting

A SIMATIC IPC can be booted remotely from a bootable ISO file

made available by another PC.

Requirement

The following requirements must be fulfilled in order to use the remote maintenance

functions:

●

A device with a processor using iAMT technology

●

A configured management engine (ME)

●

The computer must be connected to the power grid and the network.

Configuring iAMT

You configure iAMT with Intel® Management Engine BIOS Extension (MEBx) in the

firmware.
You can find information on this in the detailed firmware/BIOS description, see "Important

instructions and manuals for operating the device (Page 11)".

Software for remote maintenance of the device

You can find information about the software for remote maintenance of the device and its

documentation under:

●

SIMATIC IPC Remote Manager (Page 68)

Summary of Contents for SIMATIC IPC627E





































































































































































Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands

Siemens SIMATIC IPC627E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands