Siemens SIMATIC IPC627E Operating Instructions Manual Download

Page: 42 / 164

Installing and connecting the device

3.2 Installing the device

SIMATIC IPC627E

Operating Instructions, 12/2018, A5E44297201-AA

3.2.3

Installation of the device with wall mounting rails

The included wall mounting rails allow for space-saving installation of the device.

Note
See the notes under "Mounting positions (Page 41)".

Mounting of the mounting rails on the device

Remove the equipotential bonding screw

①

from the device and attach it to the wall

mounting rails.

Secure the wall mounting rails to the device using the following number of screws:
–

SIMATIC IPC627E: Six M4 screws; torque 3 Nm

Summary of Contents for SIMATIC IPC627E





































































































































































Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands

Siemens SIMATIC IPC627E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands