Siemens SIJECT15 Operation Manual Download

Page: 52 / 91

SIJECT OP15B Screens

SIJECT 15/16 Operation Manual June, 2003

3-18

Mold open time (TmMldOpn)

－

The total time for mold open, which is

monitoring time. There is event message if the setting time is exceeded.

Carriage advance time (TmCarAdv)

－

The total time for carriage

advance, which is monitoring time. There is event message if the setting
time is exceeded.

Carriage retract time (TmCarRet)

－

The total time for carriage retract,

which is monitoring time. There is event message if the setting time is
exceeded.

Ejector advance time (TmEjeAdv)

－

The total time for ejector

advance, which is monitoring time. There is event message if the setting
time is exceeded.

Ejector retract time (TmEjeRet)

The total time for ejector retract, which

is monitoring time. There is event message if the setting time is
exceeded.

Pre-decompression time (TmPreDec)

－

The total time for pre-

decompression, which is monitoring time. There is event message if the
setting time is exceeded.

Decompression time (TmDec)

－

The total time for decompression,

which is monitoring time. There is event message if the setting time is
exceeded.

Charging time (TmCha)

－

The total time for charging, which is

monitoring time. There is event message if the setting time is exceeded.

Summary of Contents for SIJECT15




























































































Search results

Summary of Contents for SIJECT15

Reviews:

Related manuals for SIJECT15

Brands by name

Popular brands

Siemens SIJECT15, Operation Manual

Search results

Summary of Contents for SIJECT15

Reviews:

Related manuals for SIJECT15

Brands by name

Popular brands