Siemens SIJECT15 Operation Manual Download

Page: 76 / 91

SIJECT OP15B Screens

SIJECT 15/16 Operation Manual June, 2003

3-42

3.2.3 Carriage Screen

Fig

3-33 Carriage

screen

Operating sequences

Press the middle key to enter the carriage screen. See Fig 3-33.

The status of carriage advance and retract is displayed here, also the
mode of feeding.

Carriage advance (CarAdv)

－

set the pressure and flow of carriage

advance.

Carriage retract (CarRet)

－

set the pressure, flow and time of carriage

retract. The time set here is used for monitoring the carriage retract. If
carriage does not retract to the end during this time, then it will send
alarm.

Feeding mode (Feed mode)

－

there are three modes for feeding: fixed,

front and back.

Fixed feeding: the carriage is fixed, first charging then decompression.

Front feeding: the carriage is at the front, first charging then
decompression, then the carriage will retract.

Back feeding: the carriage will retract first, then charging and
decompression.

Press

key to make carriage retract manually.

Press

key to make carriage advance manually.

Summary of Contents for SIJECT15




























































































Search results

Summary of Contents for SIJECT15

Reviews:

Related manuals for SIJECT15

Brands by name

Popular brands

Siemens SIJECT15, Operation Manual

Search results

Summary of Contents for SIJECT15

Reviews:

Related manuals for SIJECT15

Brands by name

Popular brands