Siemens SCALANCE XR324-4M EEC Compact Operating Instructions Download Page 9

Page: 9 / 84

Device defective

If a fault develops, please send the device to your SIEMENS service center for repair. Repairs

on-site are not possible.

Recycling and disposal

The products are low in pollutants, can be recycled and meet the requirements of the WEEE

directive 2012/19/EU for the disposal of electrical and electronic equipment.
Do not dispose of the products at public disposal sites.
For environmentally friendly recycling and the disposal of your old device contact a certified

disposal company for electronic scrap or your Siemens contact (Product return (

https://

support.industry.siemens.com/cs/ww/en/view/109479891

)).

Note the different national regulations.
SIMATIC NET, SCALANCE, C-PLUG, OLM

Trademarks

The following and possibly other names not identified by the registered trademark sign

are

registered trademarks of Siemens AG:

Introduction

SCALANCE XR-300M EEC

Compact Operating Instructions, 11/2019, A5E02661176-14

Summary of Contents for SCALANCE XR324-4M EEC





















































































Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands

Siemens SCALANCE XR324-4M EEC, Compact Operating Instructions

Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands