Siemens SCALANCE XR324-4M EEC Compact Operating Instructions Download Page 73

Page: 73 / 84

The following types of protection are possible:
● nA

IECEx classification: Ex nA IIC T4 Gc

Certificate no.: DEK 14.0025X

The products meet the requirements of the following standards:
– IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of

protection "n")

– IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)

● nA [op is]

IECEx classification: Ex nA [op is Gb] IIC T4 Gc

Certificate no.: DEK 14.0026X

The products meet the requirements of the following standards:
– IEC 60079-28 (Explosive atmospheres - Part 28: Protection of equipment and

transmission systems using with optical radiation)

– IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of

protection "n")

– IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)

● ec

IECEx classification: Ex ec IIC T4 Gc

Certificate no.: DEK 18.0017X

The products meet the requirements of the following standards:
– IEC 60079-7 (Explosive atmospheres - Part 7: Equipment protection through increased

safety "e")

– IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)

You will find the current versions of the standards in the currently valid IECEx certificates.

Note
Only variants with 24 VDC power supply meet the requirements of this approval.

Note for devices with CLASS 1 LASER

Important note on products certified according to Type Examination Certificate KEMA

07ATEX0145 X as of Issue 95 / DEKRA 18ATEX0025X and IECEx Certificate of Conformity

DEK 14.0025X as of Issue 43 / DEK 18.0017X and containing Class 1 optical radiation sources.

Note
CLASS 1 LASER
The device contains optical radiation sources which comply with the limits of Class 1 according

to IEC 60825-1. Fiber-optic cables connected to these optical radiation sources may therefore

be routed either to or through hazardous areas requiring Category 2G, 3G, 2D or 3D

equipment.

Approvals

SCALANCE XR-300M EEC

Compact Operating Instructions, 11/2019, A5E02661176-14

Summary of Contents for SCALANCE XR324-4M EEC





















































































Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands

Siemens SCALANCE XR324-4M EEC, Compact Operating Instructions

Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands