Siemens SCALANCE XR324-4M EEC Compact Operating Instructions Download Page 29

Page: 29 / 84

Assembling

5.1

Safety notices for installation

Safety notices

When installing the device, keep to the safety notices listed below.

WARNING

If a device is operated in an ambient temperature of more than 50 °C, the temperature of the

device housing may be higher than 70 °C. The device must therefore be installed so that it is

only accessible to service personnel or users that are aware of the reason for restricted access

and the required safety measures at an ambient temperature higher than 50 °C.

WARNING

If the device is installed in a cabinet, the inner temperature of the cabinet corresponds to the

ambient temperature of the device.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD
Replacing components may impair suitability for Class 1, Division 2 or Zone 2.

WARNING

The device may only be operated in an environment with pollution degree 1 or 2 (see

IEC 60664-1).

WARNING

The device is intended for indoor use only.

SCALANCE XR-300M EEC

Compact Operating Instructions, 11/2019, A5E02661176-14

Summary of Contents for SCALANCE XR324-4M EEC





















































































Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands

Siemens SCALANCE XR324-4M EEC, Compact Operating Instructions

Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands