Siemens SCALANCE XR324-4M EEC Compact Operating Instructions Download Page 38 | Manualshive

Page: 38 / 84

background image

3.

Place the media module in the guide rails of the device

slot.
The media module is correctly installed when it clips easi‐

ly into the device.

4.

Push the handle back into the media module. This locks

the media module in the device.

5.

Insert the connectors.

Removing a media module

CAUTION

Risk of burns due to the high temperature of the module housing
Turn off the device and allow the device to cool down before you remove a media module.

1. Remove all connectors from the media module.
2. Pull out the handle of the media module and remove the media module from the device slot.
3. Secure the dummy cover.

Assembling
5.5 Installation of modular devices

SCALANCE XR-300M EEC

38

Compact Operating Instructions, 11/2019, A5E02661176-14

«
...
36
37
38
39
40
...
»

Summary of Contents for SCALANCE XR324-4M EEC





















































































Reviews:

No comments

Related manuals for SCALANCE XR324-4M EEC

Brand: Accelerated Pages: 10

Brand: Accelerated Pages: 4

TOWERCHRON DP72

Brand: Grasslin Pages: 2

Brand: APM Pages: 3

Brand: Patton electronics Pages: 23

TRAK 2OP M11 Mill

Brand: XYZ Machine Tools Pages: 203

Brand: Patton electronics Pages: 9

Brand: Qlogic Pages: 8

Brand: Gira Pages: 6

Brand: StarTech.com Pages: 9

Brand: Paradyne Pages: 6

GSM7224v2 - Layer 2 Managed Gigabit Switch

Brand: NETGEAR Pages: 3

Brand: CalAmp Pages: 115

Brand: Ubiquiti Pages: 23

Brand: Dahua Pages: 113

Brand: NETGEAR Pages: 152

WebShare 141 WN

Brand: Atlantis Pages: 78

Brand: Carrier Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands