Siemens SCALANCE XR324-4M EEC Compact Operating Instructions Download Page 40

Page: 40 / 84

Select the required SFP media module in the slot of

the device. (Example: X-308-2M, slot 2)

Insert the SFP with the clip closed in the SFP media

module.
Notice: Closing the clip after insertion does not lock

the device in the rack.

The SFP can be heard to lock in place and is there‐

fore firmly secured.

Plug the connecting cable into the SFP.

The connecting cable can be heard to lock in place

and is then firmly secured.

Removing an SFP

1. Remove the cable connected to the SFP.
2. Open the clip on the SFP and remove the SFP from the SFP media module.

Notice: It must be possible to remove the SFP easy without using force.

3. Fit a blind plug to the SFP.

Assembling
5.5 Installation of modular devices

SCALANCE XR-300M EEC

Compact Operating Instructions, 11/2019, A5E02661176-14

Summary of Contents for SCALANCE XR324-4M EEC





















































































Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands

Siemens SCALANCE XR324-4M EEC, Compact Operating Instructions

Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands