Siemens SCALANCE XR324-4M EEC Compact Operating Instructions Download Page 39

Page: 39 / 84

5.5.2

SFP installation in SFP media module

NOTICE
Use only approved SFPs
If you use SFPs that are not approved by Siemens AG, there is no guarantee that the device

will function according to the specification.
If you use unapproved SFPs, this can lead to the following problems:
● Damage to the device
● Loss of the approvals
● Violation of the EMC regulations
Use only approved SFPs.

You can insert or remove the SFP during ongoing operation.

Inserting an SFP

Note
Only the media module MM992-2SFP may be fitted with approved SFPs. The SFP media

module can be fitted with up to two SFPs.

Device:

Media module

Variant

[Article number]

Labeling on the device

Figure

MM992-2SFP

(SFP media module)

2 x 100/1000 Mbps

[6GK5 992-2AS00-8AA0]

9922AS

Assembling

5.5 Installation of modular devices

SCALANCE XR-300M EEC

Compact Operating Instructions, 11/2019, A5E02661176-14

Summary of Contents for SCALANCE XR324-4M EEC





















































































Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands

Siemens SCALANCE XR324-4M EEC, Compact Operating Instructions

Search results

Summary of Contents for SCALANCE XR324-4M EEC

Reviews:

Related manuals for SCALANCE XR324-4M EEC

Brands by name

Popular brands