Siemens RVL481 Basic Documentation Download Page 73 | Manualshive

Page: 73 / 118

background image

73/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

19 Function block "D.h.w. storage tank"

20.05.2008

19.7 Forced

charging

On operating line 131, it is possible to select whether or not forced charging of the
d.h.w. storage tank shall take place daily when d.h.w. heating is released for the first
time. With forced charging, the d.h.w. storage tank will also be charged when the d.h.w.
temperature lies between the switch-on and the switch-off temperature. The switch-off
point remains the same.
If d.h.w. heating is released 24 hours a day, forced charging takes place every day at
midnight. If activated, the legionella function also leads to forced charging.

19.8 Protection against discharging

19.8.1 Purpose

With plant types using a d.h.w. storage tank, protection against discharging is ensured
during overrun of the d.h.w. charging pump. This function makes certain that the d.h.w.
will not be cooled down again during pump overrun.

19.8.2 Mode of operation

If the flow temperature is lower than the d.h.w. storage tank temperature,

•

pump overrun will be terminated prematurely (plant types x–1, and x–2)

•

the changeover valve will be driven to the position "Heating circuit” (plant types x–3)

If the storage tank is equipped with two sensors, the sensor measuring the higher tem-
perature is considered.
The flow temperature is acquired with sensors B1 and B3, depending on the type of
plant, or obtained from the data bus (LPB) as the common flow temperature.

If the flow temperature is lower than the setpoint of the d.h.w. temperature,

•

pump overrun will be terminated prematurely (plant types x–1, and x–2)

•

the changeover valve will be driven to the position "Heating circuit” (plant types x–3)

The flow temperature is ascertained as follows, depending on the type of plant and the
bus connection:

Plant

type

Controller with no bus (LPB)

Controller with bus (LPB)

1–1

No protection against dis-
charging

Common flow temperature from data bus
(if present), otherwise no protection
against discharging

1–2

Sensor B3

Sensor B3

2–1

Sensor B1

Sensor B1

2–2

Sensor B3

Sensor B3

2–3

Sensor B1

Sensor B1

3–1

Sensor B1

Sensor B1

3–2

Sensor B3

Sensor B3

3–3

Sensor B1

Sensor B1

4–1

Sensor B1

Sensor B1

4–2

Sensor B3

Sensor B3

5–1

Sensor B1

Sensor B1

5–2

Sensor B3

Sensor B3

6–1

Sensor B1

Sensor B1

6–2

Sensor B3

Sensor B3

With storage tank
sensor(s)

With thermostat(s)

Flow temperature

«
...
71
72
73
74
75
...
»

Summary of Contents for RVL481























































































































Reviews:

No comments

Related manuals for RVL481

Brand: ABB Pages: 50

Brand: Danfoss Pages: 7

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 124

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 114

ECL Comfort 300

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 24

ECL Comfort 296

Brand: Danfoss Pages: 159

VLT AutomationDrive FC 301

Brand: Danfoss Pages: 78

Brand: Danfoss Pages: 20

ECL Comfort 100M

Brand: Danfoss Pages: 21

Brand: Danfoss Pages: 64

Brand: Uclear Pages: 40

Brand: National Instruments Pages: 2

Brand: Omega Pages: 56

Brand: Omega Pages: 2

MicroTech II UV05

Brand: AAF Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands