Siemens RVL481 Basic Documentation Download Page 72 | Manualshive

Page: 72 / 118

background image

72/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

19 Function block "D.h.w. storage tank"

20.05.2008

19.4 Boost of the d.h.w. charging temperature

The boost of the d.h.w. charging temperature in °C can be set on operating line 127.
The boost refers to the setpoint of the d.h.w. temperature.
The lower the setting of this value, the longer d.h.w. charging takes.

T

Lw

= T

BWw

+ T

BW

∆

[°C]

Setpoint of d.h.w. temperature (T

BWw

, operating line 26)

= 50 °C

Boost of the d.h.w. charging temperature (T

BW

∆

, operating line 127) = 10 °C

Resulting setpoint of the charging temperature T

Lw

= 60 °C

If thermostats are used, the boost of the d.h.w. charging temperature must still be set.

19.5 Maximum d.h.w. charging time

The maximum charging time for d.h.w. storage tanks can be set on operating line 129.
This function is always active, independent of the kind of d.h.w. priority (absolute, shift-
ing, or parallel).
As soon as d.h.w. charging starts, a counter records the charging time. If charging is
terminated before the set maximum charging time has expired, the counter will be set
to zero. A new charging cycle can commence at any time.
However, if charging takes longer than the set maximum time, charging will be stopped
and than locked for the same period of time. Then, charging will be resumed either until
the setpoint is reached or maximum limitation terminates the charging time again.
This function can be deactivated, in which case the charging time will not be limited.

B

WL

t

2541

D

0

3

ON

OFF

t

T

BWw

T

BW

T

BWw

- SD

BW

t

Lmax

t

Lmax

D.h.w. charging locked

B

WL

D.h.w. charging

ON

D.h.w. charging ON

OFF

D.h.w charging OFF

t Time

t

Lmax

Maximum charging time

T

BW

D.h.w.

temperature

TBWw D.h.w temperature setpoint

SDBW Switching

differential

d.h.w.

19.6 Setpoint of legionella function

On operating line 130, the setpoint of the legionella function can be adjusted or the
function deactivated. This function raises the d.h.w. temperature periodically, thus mak-
ing certain that legionella bacteria will be killed. For description, refer to chapter
"23 Function block "Legionella function"

Example

«
...
70
71
72
73
74
...
»

Summary of Contents for RVL481























































































































Reviews:

No comments

Related manuals for RVL481

Brand: ABB Pages: 120

Brand: ABB Pages: 42

Brand: QCON Pages: 4

Brand: KEB Pages: 16

Brand: Computer Automation Technology Pages: 55

Brand: Allen-Bradley Pages: 16

Brand: Ros Pages: 10

DIGI-STAR GT400

Brand: AGRI TRONIX Pages: 26

Brand: Tescom Pages: 15

Brand: JENCO Pages: 31

Brand: Eaton Pages: 2

IC 912 Pt100-TC

Brand: Eliwell Pages: 4

Brand: Viking Electronics Pages: 12

Brand: WifiTrax Model Science Pages: 4

Brand: Shimaden Pages: 64

Brand: EPOS Pages: 21

Brand: Zero 88 Pages: 34

Brand: YASKAWA Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands