Siemens RVL481 Basic Documentation Download Page 93

Page: 93 / 118

93/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

26 Function block "D.h.w. solar charging"

20.05.2008

OFF

TSp

TKol

254

OFF

TLmin

TKol Collector

temperature

ON/OFF Collector

pump

Temperature differential ON

OFF

Temperature differential OFF

TSp

Storage tank temperature

TLmin Minimum

charging

temperature

T Temperature
t Time

•

The storage tank is charged if the collector temperature exceeds the current storage

temperature by the switch-on differential:
TKol > TSp + SD

•

Storage tank charging is stopped if the collector temperature drops below the tempera-

ture differential:
TKol < TSp + SD

OFF

26.2.2 Minimum

charging

temperature

The collector pump is commissioned only if the collector has a minimum temperature of
30 °C and the required temperature differential is reached.

OFF

TLmin 30 °C

- SD

OFF

TKol

254

TKol Collector

temperature

ON/OFF Collector

pump

Temperature differential ON

OFF

Temperature differential OFF

TLmin Minimum

charging

temperature

T Temperature
t Time

•

Charging is stopped (even if the switch-on differential is reached) if the collector tem-

perature is below the charging temperature:
TKol < TLmin

•

Charging takes place if the collector temperature exceeds the minimum charging tem-

perature (and if the required switch-on differential is reached) by the switch-on differen-
tial (SD

– SD

OFF

TKol > TLmin + (SD

– SD

OFF

)

Summary of Contents for RVL481























































































































Search results

Summary of Contents for RVL481

Reviews:

Related manuals for RVL481

Brands by name

Popular brands

Siemens RVL481, Basic Documentation

Search results

Summary of Contents for RVL481

Reviews:

Related manuals for RVL481

Brands by name

Popular brands