Siemens RVL481 Basic Documentation Download Page 8

Page: 8 / 118

8/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

Contents

20.05.2008

20.1

Operating lines...............................................................................................75

20.2

Function .........................................................................................................75

20.2.1

Flow temperature boost .................................................................................75

20.2.2

D.h.w temperature control..............................................................................75

20.3

Pulse lock.......................................................................................................75

Function block "Derivative action time d.h.w. heating via heat exchanger"76

21.1

Operating line.................................................................................................76

21.2

Description .....................................................................................................76

Function block "Multi-functional relay"........................................................77

22.1

Operating lines...............................................................................................77

22.2

Functions .......................................................................................................77

22.2.1

No function.....................................................................................................77

22.2.2

Outside temperature switch ...........................................................................77

22.2.3

ON / OFF according to the time switch ..........................................................78

22.2.4

Relay energized in the event of fault..............................................................78

22.2.5

Relay energized during occupancy time ........................................................78

22.2.6

Relay energized during occupancy time (including optimizations) ................78

22.2.7

Relay energized, if there is demand for heat .................................................78

22.2.8

Manually ON / OFF ........................................................................................78

Function block "Legionella function" ........................................................79

23.1

Operating lines...............................................................................................79

23.1.1

Periodicity of legionella function.....................................................................79

23.1.2

Time of legionella function .............................................................................79

23.1.3

Dwelling time at the legionella setpoint..........................................................79

23.1.4

Circulating pump operation during the legionella function .............................79

23.2

Mode of operation ..........................................................................................80

Function block "Switching program 3".......................................................81

24.1

Operating lines...............................................................................................81

24.2

Function .........................................................................................................81

Function block "Service functions and general settings" .......................82

25.1

Operating lines...............................................................................................82

25.2

Display functions............................................................................................82

25.2.1

Flow temperature setpoint .............................................................................82

25.2.2

Heating curve.................................................................................................83

25.2.3

Hours run counter ..........................................................................................83

25.2.4

Software version ............................................................................................84

25.2.5

Identification number of room unit..................................................................84

25.3

Commissioning aids.......................................................................................84

25.3.1

Simulation of the outside temperature ...........................................................84

Summary of Contents for RVL481























































































































Search results

Summary of Contents for RVL481

Reviews:

Related manuals for RVL481

Brands by name

Popular brands

Siemens RVL481, Basic Documentation

Search results

Summary of Contents for RVL481

Reviews:

Related manuals for RVL481

Brands by name

Popular brands