manualshive.com logo in svg

Siemens MAMMOMAT Balance, Troubleshooting Manual, Page: 48 / 62

Share
Download
Siemens MAMMOMAT Balance Troubleshooting Manual Download Page 48

Dose calculator

 

MAMMOMAT Balance 

SPB7-115.840.01      Page 48 of 62 

Siemens AG 

Troubleshooting Guide 

Rev.02        10.04 

Medical Solutions  

 

The curve is drawn on the canvas 
of the main window, while data are 
reported into a separated window, 
from which you can edit them. This 
window is always "on the top" and 
you can move it to discover parts of 
the graphic below, but if you close 
it, the graphic disappears too.  

 

 

Data are presented in a "kV" versus "Correction factor" grid. Any row 
corresponds to a point of the curve.  

 

To insert a new value in the table, right-click the 
mouse over an existing one and choice "Insert".  

 

A "New kV" dialog pops-up. Type 
the desired new value and press 
OK.  

 

A "New Factor" dialog pops-up. 
Type the desired new value and 
press OK. The table, and the graph 
below, are updated. The ranges of 
possible values for kV and Factor 
are those shown in the graph axes. 
Any value outside this ranges pops-
up an error message and quits the 

Summary of Contents for MAMMOMAT Balance































































Reviews:

No comments