Siemens MAMMOMAT Balance Troubleshooting Manual Download Page 40 | Manualshive

Page: 40 / 62

Siemens MAMMOMAT Balance Troubleshooting Manual Download Page 40

Dose calculator

MAMMOMAT Balance

SPB7-115.840.01 Page 40 of 62

Siemens AG

Troubleshooting Guide

Rev.02 10.04

Medical Solutions

The "Open file" window
opens, showing a list of
available files. The
directory first opened is
the one stored in the
Deata Plus setup file
and selected with the
"Option"-"Define path"
menu. Anyways, you
can select another
doubleclicking in the
filelist on the left.
Double-clicking the
desired configuration in
the rightmost list, all the
necessary files are
open and loaded in the
program.
In the rightmost list you
will find one
configuration per any
mammo unit that you
previously created by
the Deata Plus
program.

So that you don’t need to create a new skin dose file for a mammo unit and you cannot delete it.

The Deata Plus program does this for you, with a default set of values at creation, and deleting the skin
dose file when a mammo unit is deleted using the Deata Plus program.

The "Open file" window closes and
the main window reflects the
loading of the correct configuration
file showing the characteristics of
the dosemeter and the name of the
file.

«
...
38
39
40
41
42
...
»

Summary of Contents for MAMMOMAT Balance































































Reviews:

No comments