manualshive.com logo in svg

Siemens MAMMOMAT Balance, Troubleshooting Manual, Page: 18 / 62

Share
Download
Siemens MAMMOMAT Balance Troubleshooting Manual Download Page 18

Troubleshooting

 

MAMMOMAT Balance 

SPB7-115.840.01      Page 18 of 62 

Siemens AG 

Troubleshooting Guide 

Rev.02        10.04 

Medical Solutions  

 

ALARM 

TUBE THERMAL LIMIT REACHED 

Code 

HU

 

When 

Starting exposure 
 

Why 

X-ray tube assembly has reached maximum operating temperature. 
 

Action 

Wait for tube cooling. 
Evaluate operating conditions from last 1300 exposure memory. 
Check tube temperature sensor PCB 02-171. 
Disable tube rotation brake. 
 

 
 

ALARM 

TECHNICAL ERROR 

Code 

Refer to list

 

When 

Any time. 
 

Why 

Internal error having no meaning for the operator. 
 

Action 

Check Log File to find out what it is. 
Date and time of error / fault can be helpful to locate it quickly   
 

 
 
 
 
 
 

2) Technical menu 

 

When 

Any time. 
 

Why 

Broken Fuse or defective block has been located by CPU diagnostic functions 
 

Action 

Check Log File to find out when it occurred 
 

 
 

SIEMENS AG 

CPU 01-170         F2=OK    F4=OK 

SW1  00000000           SW2  0000 

INVERTER  Vdc (in)  =  545 V         LV= OK 

Filament                92-073                >> PASS << 

Rotating Anode     92-074                >> PASS << 

FIRMWARE REV       BAL__ XX TUBE 

Tube Housing  kJ                

25°C 

n. .............. 

../../..   .................. 

 

Summary of Contents for MAMMOMAT Balance































































Reviews:

No comments