manualshive.com logo in svg

Siemens MAMMOMAT Balance, Troubleshooting Manual, Page: 14 / 62

Share
Download
Siemens MAMMOMAT Balance Troubleshooting Manual Download Page 14

Troubleshooting

 

MAMMOMAT Balance 

SPB7-115.840.01      Page 14 of 62 

Siemens AG 

Troubleshooting Guide 

Rev.02        10.04 

Medical Solutions  

 

ALARM 

CHECK ARM PUSH BUTTON 

CHECK BRAKE PUSH BUTTONS 

CHECK FOOT PEDAL SWITCH 

Code 

Pa 

Pb 

Pc 

When 

during operating of compression or c-arm rotation or c-arm vertical movement or anytime 
for eventual malfunction of pushbuttons or foot pedal switches 
. 

Why 

pushbutton or foot pedal switch of mentioned functions remains activated for more than 
20” 
 

Action 

Check pushbuttons or foot pedal switches and eventually disconnect them from the 
boards for easier investigation. 
 

Note 

Alarm goes OFF by itself if normal condition is restored releasing pushbutton or foot pedal 
switch. 
 

 
 

ALARM 

CHECK CASSETTE 

Code 

Ci

 

When 

At power ON 
 

Why 

Cassette was inside the table and could be exposed. 
 

Action 

Remove cassette check it and reinsert. 
If alarm comes out without cassette inside check cassette sensing microswitches. 
 

Note 

Alarm goes OFF by itself if normal condition is restored removing cassette  
 

 
 

ALARM 

DOOR OPEN 

Code 

Do

 

When 

Starting exposure  
 

Why 

Door of Examination room was open when operator pressed x-ray push button 
 

Action 

Close door or check door contact and / or wiring to PCB 03-186. 
 

Note 

Alarm goes OFF by itself if normal condition is restored closing the door. 
Exposure is not interrupted if door is open after that exposure sequence started. 
 

 

Summary of Contents for MAMMOMAT Balance































































Reviews:

No comments