Siemens MAMMOMAT Balance Troubleshooting Manual Download Page 22

Page: 22 / 62

Troubleshooting

MAMMOMAT Balance

SPB7-115.840.01 Page 22 of 62

Siemens AG

Troubleshooting Guide

Rev.02 10.04

Medical Solutions

List of Error codes

A full list of error codes is given below::

Exposure terminated without problems.

CODE

Description

EXPOSURE TERMINATED BY FILM AEC

EXPOSURE TERMINATED BY mAs INTEGRATOR

Exposure terminated with problems.

CODE

Fault description

EARLY PUSH BUTTON RELEASE

LOW mAs SELECTION WITH AEC

EXPOSURE TERMINATED BY BACK UP TIMER

ANODE STARTER FAILED DURING PREPARATION

FILAMENT FAILED DURING PREPARATION

ANODE STARTER FAILED DURING EXPOSURE

FILAMENT FAILED DURING EXPOSURE

Operating or system errors with sample pulse x-ray emission only

CODE

Fault description

BREAST TOO DENSE

AEC DETECTOR OVER EXPOSED

Operating errors without x-ray emission

CODE

Fault description

DOOR OPEN

ABSENCE OF COLLIMATOR CONE

CASSETTE NOT INSERTED

CASSETTE IN AT POWER ON

CASSETTE ALREADY EXPOSED

NOT ACTIVE

System errors and or faults

CODE

Fault description

GAS SPRING DEFECTIVE

CHECK BRAKE PUSH BUTTONS

CHECK ARM PUSH BUTTON

CHECK FOOT PEDAL SWITCH

FILTER POSITION ERROR

MIRROR POSITION ERROR

BRAKE POSITION SWITCHES MW5 , MW6 FAILURE

BRAKE MOTOR MT3 FAILURE

TUBE TERMAL LIMIT REACHED

FUSES and blocks ( multiple fault are shown as code addition)

CODE

Fault description

INVERTER CONTROL BOARD

FILAMENT POWER SUPPLY

ROTATING ANODE STARTER

INVERTER POWER

F4 PCB 92-082

F2 + 15P PCB 92-082

F2 + 15° PCB 92-082

ANODE NOT ROTATING

Summary of Contents for MAMMOMAT Balance































































Search results

Summary of Contents for MAMMOMAT Balance

Reviews:

Siemens MAMMOMAT Balance, Troubleshooting Manual, Page: 22 / 62

Search results

Summary of Contents for MAMMOMAT Balance

Reviews: