Siemens LMV50 series Manual Download Page 71 | Manualshive

Page: 71 / 327

background image

71/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

4 Burner control

22.05.2018

4.2.4 Selection of fuel

The type of fuel is selected via the menu on the AZL5.
The selection is only possible when the fuel selector is set to

INT

(or when no selector

is connected).
Fuel selection is continuously stored via voltage-OFF, so that a valid fuel selection is
present when power returns.

It is only possible to select a fuel via the building automation and control system if the
fuel selector on the LMV5 is set to

INT

(or when no selector is connected).

Ι

Note!
Fuel selection via BACS should be cyclically repeated.
There is no definition of priorities between fuel selection via BACS and fuel selection
via the AZL5, which means that the selection used is the selection made last.

After fuel changeover, the burner control maintains or changes to standby
(

↑

Normal start). Now, a new start is made (provided there is a request for heat), firing

on the selected type of fuel.
If

↑

Direct start has been parameterized, fuel changeover can also take place upon

shutdown in phase 76. The fan is not switched off.

Selection of fuel on the
AZL5

Selection of fuel via
BACS (Modbus)

Fuel changeover

«
...
69
70
71
72
73
...
»

Summary of Contents for LMV50 series








































































































































































































































































































































Reviews:

No comments

Related manuals for LMV50 series

Brand: EAW Pages: 10

Brand: National Instruments Pages: 5

Brand: National Instruments Pages: 76

Brand: Quantum Pages: 20

Brand: Danfoss Pages: 61

Brand: Analog Devices Pages: 76

Brand: Amplifier Tech Pages: 36

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

Brand: ZALMAN Pages: 22

Brand: Renesas Pages: 4

D-NVR4108HS-4KS2/L

Brand: Dahua Pages: 33

Brand: C&T Solution Pages: 129

DataPlot CB1224

Brand: B-G Instruments Pages: 4

Brand: ANEP Pages: 48

Brand: SilverStone Pages: 28

GEFORCE RTX 4090

Brand: Nvidia Pages: 160

Brand: M-system Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands