Siemens LMV50 series Manual Download Page 48 | Manualshive

Page: 48 / 327

background image

48/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

4 Burner control

22.05.2018

4.1.5.7 Air pressure switch

(X3-02 pin 1)

An air pressure switch can be connected to these terminals.

a) The input can be activated / deactivated.

When the input is activated, air pressure is anticipated after the fan has been
switched on.
If there is no pressure signal, safety shutdown is initiated in any case.

Parameter AirPressureTest (activated / deactivated)

b) In this setting, the signal of a connected air pressure switch is not evaluated in the

home run

and

standby

phases but leads to start prevention if the signal is not

present.
In all other phases, a missing signal leads to safety shutdown in any case.

Parameter AirPressureTest (deactInStby)

4.1.5.8 Gas pressure switch - valve proving or valve closure contacts

(

X9-03

pin 2)

The input can be configured either as a pressure switch-valve proving input (PS-VP)

or

as a closed position indicator input (CPI).

PD-VP

The input is only active when firing on gas and when valve proving is activated.

↑

valve proving of gas valves

Parameter PS-VP/CPI

(PS-VP)

CPI Gas

CPI:
It is used for checking the gas valves‘ fully closed position.
For that purpose, the gas valves‘ closure contacts for the fully closed position are to be
connected in series using this input
The input is active in both gas- and oil-fired operation.

Gas-fired operation:
In phases 12 to 38 and phases 72 to 78, a check is made to ensure that the input is set
to

On

(valve closed) und in phases 54 and 60 to

Off

(valve open).

In standby,

Off

(valve open) leads to a start prevention with a display message.

The display message can be output with a time delay (can be set with parameter

DelayStartPrev

).

Oil-fired operation:
In phases 12 to 38, 54, 60 and phases 72 to 78, a check is made to ensure that the
input is set to

On

(valve closed).

In standby

Off

(valve open) leads to a start prevention with a display message.

The display message can be output with a time delay (can be set with parameter

DelayStartPrev

).

Parameter PS-VP/CPI (CPI or CPI Gas)

«
...
46
47
48
49
50
...
»

Summary of Contents for LMV50 series








































































































































































































































































































































Reviews:

No comments

Related manuals for LMV50 series

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: Ublox Pages: 116

Brand: IEI Technology Pages: 3

Brand: Furuno Pages: 24

Brand: Stanwax Laser Pages: 9

Brand: Roland Pages: 12

Momentum ROG Strix X570-E D-RGB

Brand: EK-Quantum Pages: 10

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

HBJC924R3288DG2NS Series

Brand: JETWAY Pages: 6

Brand: Datasat Pages: 24

Brand: Galaxy Pages: 30

Brand: ANEP Pages: 48

Brand: Microchip Technology Pages: 9

Brand: Alula Pages: 4

Brand: Logicube Pages: 56

Brand: Active Communications Pages: 10

Brand: VideoWave Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands