Siemens LMV50 series Manual Download Page 127 | Manualshive

Page: 127 / 327

background image

127/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

7 Boiler controller / load controller

22.05.2018

7.8.3 Cold start thermal shock protection with temperature

sensor in pressure plants

In pressure plants, thermal shock protection can also be implemented with a
temperature sensor (additional sensor), as an alternative to the pressure sensor.
If an additional temperature sensor is installed and activated (

Additional Sensor

set to

Pt100

or

Pt1000

or

Ni1000),

for the CSTP function the temperature signal from this

additional sensor is used instead of the pressure signal from the boiler controller and
also the temperature setpoint for the additional sensor (

Setpoint AddSens)

is used.

The parameters

ThresholdOn

and

ThresholdOff

are then percentage values from this

temperature setpoint (

Setpoint AddSens)

of the additional sensor

.

Parameter

Additional Sensor (deactivated / Pt100 / Pt1000 / Ni1000)
Setpoint AddSens
Temp. ColdStart

Caution!
When using a pressure sensor, the temperature limiter is not active.

«
...
125
126
127
128
129
...
»

Summary of Contents for LMV50 series








































































































































































































































































































































Reviews:

No comments

Related manuals for LMV50 series

Brand: TC Electronic Pages: 2

PCMCIA WIRELESS ASAPTER DWL-650

Brand: D-Link Pages: 5

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

Brand: Vanguard Pages: 4

Brand: Garland Pages: 6

Brand: Industrex Pages: 51

HiGain HLU-231 List 8F

Brand: ADC Pages: 7

Brand: Ruckus Wireless Pages: 56

Brand: Renesas Pages: 6

MultiConnect SE MTS2EA

Brand: Multitech Pages: 8

Brand: SurfControl Pages: 2

iCE40 SPRAM Series

Brand: Lattice Semiconductor Pages: 12

Brand: ICS ELECTRONICS Pages: 4

Brand: Microcomputer Systems Pages: 21

Brand: EVGA Pages: 3

Brand: RAK Pages: 14

Brand: LevelOne Pages: 61

Brand: Siklu Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands