Siemens LMV50 series Manual Download Page 66 | Manualshive

Page: 66 / 327

background image

66/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

4 Burner control

22.05.2018

4.2.3.6 Prepurging

The prepurge position is approached in phase

Traveling to prepurging

(24).

The prepurge time is determined via the following parameters:

Parameter PrepurgeTmeGas

PrepurgeTmeOil

These 2 parameters determine the minimum prepurge time, provided the following
parameters do not become effective.
This means that the prepurge time is allocated to phases 30 through 34:
In phase 30, the time defined in

PrepurgePt1...

is observed, followed by phase 32 or

valve proving. Then, the time of

PrepurgeTmeGas

possibly remaining, or

PrepurgeTmeOil

in phase 34, is observed, but always

PrepurgePt3...

as a minimum.

These parameters determine the prepurge time after the following events:
• Alterable lockout position
• Off time >24 hours (standby)
• Power failure (Power-on)
• Shutdown due to interruption of gas supply (safety shutdown)

Parameter PrepurgeSafeGas

PrepurgeSafeOil

If these times are used, they are equally assigned to phases 30 and 34.

These are minimum times that are always observed in phases 30 (prepurge time 1) and
34 (prepurge time 3)!
These parameters determine the minimum times for prepurging part 1 and part 3.

Parameter PrepurgePt1Gas

PrepurgePt1Oil
PrepurgePt3Gas
PrepurgePt3Oil

Example:
If the sum of prepurge time part 1 and part 3 exceeds

PrepurgeTmeXX

or

PrepurgeSafeXX

, this longer prepurge time applies!

When using valve proving and 2 class «A» fuel valves, prepurging will not be required
(as per EN 676).
Skipping prepurging can be activated through parameterization.

In spite of an activated parameter, prepurging is performed under the following
conditions:
• Alterable lockout position
• Off time >24 h (standby)
• Power failure (Power-on)
• Shutdown due to interruption of gas supply (safety shutdown)
• Direct start

Parameter SkipPrepurgeGas (deactivated / activated)

SkipPrepurgeOil (deactivated / activated)

Caution!
Deactivating valve proving does not automatically deactivate skipping
prepurging. Hence, the person making the settings must ensure that

SkipPrepurgeGas

is activated only if permitted for the relevant type of plant.

Prepurge time after
safety shutdown

Prepurge times 1 and
3

Start without prepurging

«
...
64
65
66
67
68
...
»

Summary of Contents for LMV50 series








































































































































































































































































































































Reviews:

No comments

Related manuals for LMV50 series

Brand: GE Pages: 6

Brand: Campbell Pages: 42

Brand: Magma Pages: 2

Brand: Quatech Pages: 27

Brand: Ubiquiti Pages: 3

Proventia A1204

Brand: Internet Security Systems Pages: 42

Brand: CAP-XX Pages: 8

Brand: Juniper Pages: 7

Brand: axing Pages: 52

Brand: ZALMAN Pages: 18

Brand: Idis Pages: 22

Mustang-M2AE-MX1

Brand: IEI Technology Pages: 58

Brand: ASROCK Pages: 173

Brand: Rosewill Pages: 2

Brand: LevelOne Pages: 4

VXC-114U Series

Brand: ICP DAS USA Pages: 8

BNC-08DI, BNC-16DI, BNC-16SE

Brand: Omega Engineering Pages: 25

Brand: ebm-papst Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands