Siemens LMV50 series Manual Download Page 314 | Manualshive

Page: 314 / 327

background image

314/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

22 Revision history

22.05.2018

22.2.3 Changes to the variable speed drive module

(VSD

module)

22.2.3.1 VSD module, Software from V01.30 to V01.40

1. Opening of the release contact during shutdown can be parameterized. This enables

the VSD module to use a DC break.

2. Quick shutdown of the burner when speed deviation exceeds a certain level.

22.2.3.2 VSD module, Software from V01.40 to V01.50

1. Diagnostic data.

To avoid error EC A9, DC 18 (

Page disrupted)

, statistics data are now only stored in

standby and operation.

2. Offset at setpoint output.

In some cases, the correction offset for the speed setpoint was not reset after a
safety shutdown.
This could lead to error messages. The new version eliminates this effect.

3. Internal tests.

Internal system tests have been modified, allowing the VSD test initialized by the
LMV5 to be dropped.

4. Quick shutdown.

Now, quick shutdown of the VSD is also effected in programming mode.

22.2.3.3 VSD module, software for 2012/2013 release upgrade

For the 2012/2013 release upgrade for the LMV5, the internal VSD module's software
was

not

changed, meaning that the

V01.50

version is still current.

«
...
312
313
314
315
316
...
»

Summary of Contents for LMV50 series








































































































































































































































































































































Reviews:

No comments

Related manuals for LMV50 series

Brand: GE Pages: 146

Brand: IEI Technology Pages: 21

Brand: National Instruments Pages: 28

Brand: National Instruments Pages: 19

Brand: National Instruments Pages: 103

NI PXI-1042 Series

Brand: National Instruments Pages: 12

Brand: National Instruments Pages: 4

IAR KickStart Kit TWR-K60N512-IAR

Brand: IAR SYSTEMS Pages: 8

Brand: Allnet Pages: 12

Brand: Telebyte Pages: 19

Brand: JETWAY Pages: 55

Brand: Cypress Semiconductor Pages: 16

Through Hole Power Inductors 1411

Brand: Delta Electronics Pages: 1

Brand: Omron Pages: 29

FireWire 800 ExpressCard 34

Brand: LaCie Pages: 24

airMAX NanoBridge M NBM3

Brand: Ubiquiti Pages: 24

SmartRack SR25UBEXP

Brand: Tripp Lite Pages: 4

Brand: RR-Concepts Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands