Siemens LMV50 series Manual Download Page 57

Page: 57 / 327

57/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

4 Burner control

22.05.2018

4.1.6.4 Oil valves, type SI

(X8-02, X8-03, X7-01, X7-02, X6-03)

These outputs are used for connecting the oil valves in accordance with the selected
fuel train.

↑

Fuel trains,

↑

Sequence diagrams.

Parameter

FuelTrainOil (LightOilLO / HeavyOilHO / LO w Gasp / HO w
Gasp)

(Light oil with gas pilot and heavy oil with gas pilot may only be used in connection with

Gp2

)

4.1.6.5 Gas valves, type SI

(X9-01)

These outputs are used for connecting the gas valves in accordance with the selected
fuel train.

↑

Fuel trains,

↑

Sequence diagrams.

Parameter

FuelTrainGas (DirectIgniG / Pilot Gp1 / Pilot Gp2)

4.1.6.6 Operation indication gas / oil, type SI

(X8-01)

This output shows the operating position of the LMV5.
The outputs are connected directly to valve output

V1Oil

V1Gas

. The operating

position outputs for oil and gas must not be directly connected, since a wrong contact
position of valve output 1 (unused fuel) would be detected, which would lead to lockout.

Note!
During the valve proving sequence

Filling,

gas valve (V1) is controlled, so that

Gas

displayed for a moment!

Summary of Contents for LMV50 series








































































































































































































































































































































Search results

Summary of Contents for LMV50 series

Reviews:

Related manuals for LMV50 series

Brands by name

Popular brands

Siemens LMV50 series, Manual

Search results

Summary of Contents for LMV50 series

Reviews:

Related manuals for LMV50 series

Brands by name

Popular brands