Siemens LMV50 series Manual Download Page 52 | Manualshive

Page: 52 / 327

background image

52/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

4 Burner control

22.05.2018

CPI Oil:

This is used for checking the oil valves fully closed position.
For that purpose, the valve closure contacts of the oil valves are to be connected in
series and then to this input.
The input is active both with gas-fired and oil-fired operation.

Firing on oil:
In the phases 12 to 38 and in the phases 72 to 78, the input is checked for

ON

(valve

closed) and in phases 54 and 60, the input is checked for

OFF

(valve open).

In Standby,

OFF

(valve open) results in start prevention with display message.

The display message can be output with a time delay (can be set with parameter

DelayStartPrev

).

Firing on gas:
In the phases 12 to 38, 54, 60 and in the phases 72 to 78, the input is checked for

ON

(valve closed).
In Standby,

OFF

(valve open) results in start prevention with display message.

The display message can be output with a time delay (can be set with parameter

DelayStartPrev

).

Parameter PS-VP/CPI (CPI Oil)

«
...
50
51
52
53
54
...
»

Summary of Contents for LMV50 series








































































































































































































































































































































Reviews:

No comments

Related manuals for LMV50 series

Brand: Sangoma Pages: 6

Brand: LORD Pages: 9

Brand: SIIG Pages: 12

Brand: Belkin Pages: 72

MegaRAID SATA 300-4XLP

Brand: LSI Pages: 3

DM/IP601-CPCI-100BT

Brand: Dialogic Pages: 2

Brand: Digi Pages: 116

PCM-4141 Series

Brand: Advantech Pages: 96

Brand: Hauppauge Pages: 55

IPS Pro-Module-24C-GE-BP-TM

Brand: Trend Micro Pages: 3

Brand: Aaeon Pages: 57

Brand: Juniper Pages: 196

Brand: McIntosh Pages: 44

Brand: Trend Micro Pages: 2

Brand: BOSER Technology Pages: 78

Brand: Arctic Pages: 7

NexXxoS GPX-N 970 M03

Brand: Alphacool Pages: 2

SCREENSHARE PRO

Brand: V7 Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands