Siemens DQ 4x24VDC/2A HS User Manual Download

Page: 9 / 43

Product overview

2.1 Properties

Digital output module DQ 4x24VDC/2A HS (6ES7132-6BD20-0DA0)
Manual, 03/2015, A5E34944434-AA

Properties

The module has the following technical properties:

●

Digital output module with 4 outputs (push-pull)

●

Source output (PNP, sourcing output)

●

Supply voltage L+

●

Output current 2 A (per channel)

●

Configurable substitute values (per channel)

●

Configurable diagnostics (per module)

●

Suitable for solenoid valves, DC contactors, and indicator lights

The module supports the following functions:

●

Firmware update

●

I&M identification data

●

Reconfiguration in RUN

●

PROFIenergy

●

Value status

●

Isochronous mode

●

Oversampling

●

Valve control

●

Pulse width modulation

You can configure the module with STEP 7 and with a GSD file.

Accessories

The following accessories must be ordered separately:

●

Labeling strips

●

Color identification labels

●

Reference identification label

●

Shield connector

Summary of Contents for DQ 4x24VDC/2A HS












































Search results

Summary of Contents for DQ 4x24VDC/2A HS

Reviews:

Related manuals for DQ 4x24VDC/2A HS

Brands by name

Popular brands

Siemens DQ 4x24VDC/2A HS, User Manual

Search results

Summary of Contents for DQ 4x24VDC/2A HS

Reviews:

Related manuals for DQ 4x24VDC/2A HS

Brands by name

Popular brands