Siemens DQ 4x24VDC/2A HS User Manual Download

Page: 35 / 43

Technical specifications

6.1 Technical specifications

Digital output module DQ 4x24VDC/2A HS (6ES7132-6BD20-0DA0)
Manual, 03/2015, A5E34944434-AA

6ES7132-6BD20-0DA0

Total current of outputs

Current per module, max.

8 A

Total current of outputs (per module)

Horizontal installation

•

up to 30 °C, max.

8 A; DQ mode

•

up to 40 °C, max.

6.9 A; DQ mode

•

up to 50 °C, max.

4.7 A; DQ mode

•

up to 60 °C, max.

2.5 A; DQ mode

Vertical installation

•

up to 30 °C, max.

7.2 A; DQ mode

•

up to 40 °C, max.

5.6 A; DQ mode

•

up to 50 °C, max.

4 A; DQ mode

Cable length

Shielded, max.

50 m

Unshielded, max.

50 m

Isochronous mode

Isochronous mode (application synchronized up to

terminal)

Yes; DQ and OVS operating mode only

Bus cycle time (TDP), min.

250 µs

Jitter, max.

1 µs

Interrupts/diagnostics/status information

Substitute values can be applied

Yes

Interrupts

Diagnostic interrupt

Yes

Diagnostics alarms

Diagnostics

Yes

Monitoring of supply voltage

Yes

Short-circuit

Yes

Diagnostics indicator LED

Monitoring of the supply voltage (PWR LED)

Yes; green PWR LED

Channel status display

Yes; green LED

For module diagnostics

Yes; green/red DIAG LED

Electrical isolation

Electrical isolation of channels

Between the channels

Between the channels and the backplane bus

Yes

Permissible potential difference

Between different circuits

75 V DC / 60 V AC (basic insulation)

Insulation

Insulation tested with

707 V DC (type test)

Summary of Contents for DQ 4x24VDC/2A HS












































Search results

Summary of Contents for DQ 4x24VDC/2A HS

Reviews:

Related manuals for DQ 4x24VDC/2A HS

Brands by name

Popular brands

Siemens DQ 4x24VDC/2A HS, User Manual

Search results

Summary of Contents for DQ 4x24VDC/2A HS

Reviews:

Related manuals for DQ 4x24VDC/2A HS

Brands by name

Popular brands