Siemens DQ 4x24VDC/2A HS User Manual Download

Page: 37 / 43

Technical specifications

6.2 Derating of the DQ 4x24VDC/2A HS

Digital output module DQ 4x24VDC/2A HS (6ES7132-6BD20-0DA0)
Manual, 03/2015, A5E34944434-AA

Maximum permitted output current depending on the ambient temperature

In addition to the dependency of the maximum permitted output current on the frequency,

you also have to take into consideration the dependency on the ambient temperature.

Depending on the configured module operating mode, there is an additional "DQ" or "PWM"

derating. The table below shows the dependencies of derating version and module operating

mode:

Table 6- 1

Additional derating versions of the DQ 4×24VDC/2A HS

Derating version

Operating mode

Normal operation Valve control in normal operation Pulse width modulation

Oversampling

DQ derating

PWM derating

DQ derating
The figure below shows the maximum permitted total current depending on the ambient

temperature for the DQ derating.

①

Horizontal installation position

②

Vertical installation position

Figure 6-2

Additional DQ derating depending on the ambient temperature

Summary of Contents for DQ 4x24VDC/2A HS












































Search results

Summary of Contents for DQ 4x24VDC/2A HS

Reviews:

Related manuals for DQ 4x24VDC/2A HS

Brands by name

Popular brands

Siemens DQ 4x24VDC/2A HS, User Manual

Search results

Summary of Contents for DQ 4x24VDC/2A HS

Reviews:

Related manuals for DQ 4x24VDC/2A HS

Brands by name

Popular brands