Siemens BANY Agent Compact Operating Instructions Download Page 23 | Manualshive

Page: 23 / 46

background image

BANY Agent

23

Compact Operating Instruction

Installation

Install the BANY Agent on a 35 mm DIN rail complying with DIN EN 50022.

1. Hang the BANY Agent on the DIN rail and then push it in against the rail until it clips

into place..

2.  Fit the connectors for the power supply.
3.  Fit the connectors for the digital In/Outputs.
4.  Insert the terminal blocks into the sockets on the BANY Agent.

Removing

To remove an BANY Agent from the DIN rail:

1. Disconnect all cables from the BANY Agent
2. Release the lower part of the switch away from the DIN rail.

«
...
21
22
23
24
25
...
»

Summary of Contents for BANY Agent















































Reviews:

No comments

Related manuals for BANY Agent

Brand: TCS Pages: 16

Brand: Teac Pages: 3

Brand: Pentatech Pages: 38

Brand: Bentel Security Pages: 4

Brand: HomeMatic Pages: 68

Brand: Thermo Scientific Pages: 68

StorageWorks DS-BA35X-MN

Brand: Digital Equipment Pages: 2

Brand: urmet domus Pages: 52

Brand: FAAC Pages: 34

SC600 Marcopolo

Brand: Valeo Pages: 12

Brand: Ravaglioli Pages: 68

Nitrogen Pac SC-W

Brand: UNITED Pages: 112

Easy Chime OUKQH-0761

Brand: 1byone Pages: 7

Brand: Comelit Pages: 32

Brand: Aewin Pages: 42

Brand: Magnavox Pages: 1

Brand: 2easy Pages: 12

Brand: Johnson Controls Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands