Siemens BANY Agent Compact Operating Instructions Download Page 5

Page: 5 / 46

BANY Agent

Compact Operating Instruction

5.1

Notes on commissioning .............................................................................................26

5.2

Power supply - general ...............................................................................................26

5.3

Power supply ..............................................................................................................27

5.3.1

Connecting the power supply ...............................................................................27

5.3.2

24 V DC – product group BANY Agent.................................................................28

5.4

Digital In/Outputs ........................................................................................................29

5.5

Connecting functional ground......................................................................................29

Technical data ...................................................................................................................30

6.1

Construction, installation and environmental conditions ..............................................30

6.2

Connectors and electrical data ....................................................................................31

6.3

Cable lengths ..............................................................................................................33

6.4

Other properties ..........................................................................................................34

Dimension drawings ...........................................................................................................35

7.1

BANY Agent with TAP.................................................................................................35

7.2

BANY Agent without TAP ............................................................................................38

Approvals ...........................................................................................................................41

8.1

BANY Agent approvals, certificates.............................................................................41

8.2

BANY Agent Conformity certificates ............................................................................44

8.3

Overview of BANY Agent approvals ............................................................................45

8.4

Mechanical stability (in operation) BANY Agent ..........................................................45

Summary of Contents for BANY Agent















































Search results

Summary of Contents for BANY Agent

Reviews:

Related manuals for BANY Agent

Brands by name

Popular brands

Siemens BANY Agent, Compact Operating Instructions

Search results

Summary of Contents for BANY Agent

Reviews:

Related manuals for BANY Agent

Brands by name

Popular brands