Siemens ADSL 500 User Manual Download Page 62 | Manualshive

Page: 62 / 73

background image

SANTIS ADSL 50/500 User Manual

MER Mode

BRAS

Broadband Remote Access Server

PPPoE Clent

S/W

RADIUS

Server

MER

MER
Mode

PC(s)

BRAS

STM-1

DSLAM

ADSL
Router

Loop

ISP

AAA

Default Private IP
192.168.1.1

Public IP assigned
by BRAS

Description:

In this deployment environment, we make up a private IP network of 192.168.1.1. NAT function is enabled to support
multiple clients to access Internet.

In this example, the ADSL Router acts as NAT device, which translate a private IP address into a public address.
Therefore multiple users can share with one public IP address to access Internet through this router. The public
address can be a static public address that is pre-assigned by ISP or a dynamic public address that is assigned by ISP
DHCP server.

Configuration:

1.

Start up your browser and type

192.168.1.1

as the address to enter this ADSL web-based manager.

2. Go

to

Advanced User > Configuration > WAN Configuration > Create a new PVC

and select the Data

Mode –

RFC1483 MER

. Then click

Next

button.

3.

Enter the VPI/VCI values provided by your ISP and select the encapsulation type as

LLC/SNAP

or

VC MUX

.

Then click

Apply

.

4.

Set IP configuration for Local WAN IP Address. Choose

Specify an IP Address

item. Please set as the

following example,
IP Address:

10.3.86.105

(should be the one that you get from ISP)

Subnet Mask:

255.255.255.0

5. Go

to

Configuration > IP Route

and click

Create a new route

to add a new route. Configure the settings as

the following example,
Destination Address:    leave default
Netmask:

leave default

Forward packets to:

Gateway Address: 10.3.86.1

(you should get this value from your ISP)

Then click

Apply

.

6. Go

to

Configuration > DNS

and enable

DNS Relay

setting and click

Next

. On the DNS Relay web page, enter

the DNS Server IP address, for example

168.95.1.1

(you should get this value from your ISP).

7.

Save the configuration from

System

>

Save Configuration

and

System

>

Restart

to restart your router for

initiating these settings.

8.

Then you have set the web configuration successfully. And you can surf on the Internet.

62

«
...
60
61
62
63
64
...
»

Summary of Contents for ADSL 500










































































Reviews:

No comments

Related manuals for ADSL 500

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 86

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Maestro E220 Series

Brand: Lantronix Pages: 25

Brand: T&D Pages: 122

Brand: TP-Link Pages: 3

Brand: NETGEAR Pages: 14

NetVanta 6355 PoE

Brand: ADTRAN Pages: 46

Brand: BSD Networks Pages: 7

Brand: Juniper Pages: 825

Brand: Gemtek Systems Pages: 51

Brand: RubyTech Pages: 25

Brand: Zhone Pages: 53

Total Access 1500 Dual FXS/DPO

Brand: ADTRAN Pages: 2

Brand: DHD Power Cruiser Pages: 60

Brand: Matrix Switch Corporation Pages: 60

USB device 622x

Brand: National Instruments Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands