Siemens ADSL 500 User Manual Download Page 5 | Manualshive

Page: 5 / 73

background image

Chapter 1: Overview

Before You Use

The SANTIS ADSL 50/500 is an Asymmetric Digital Subscriber Line (ADSL) Router. With the asymmetric
technology, this device runs over standard copper phone lines. In addition, ADSL allows you to have both voice and
data services in use simultaneously all over one phone line.

The SANTIS ADSL 50/500 is designed to offer cost-effective high-speed services for home or office users. It
provides a downstream rate of up to 8 Mbps and upstream rate of up to 1 Mbps for ADSL connection, even offers
auto-negotiation capability for different flavors (ANSI T1.413 Issue 2, G.lite, G.dmt for Annex A, G.dmt for Annex B
or G.hs) according to central office DSLAM’s settings (Digital Subscriber Line Access Multiplexer). Also the
feature-rich routing functions are seamlessly integrated to ADSL service for existing corporate or home users. Now
users can enjoy various bandwidth-consuming applications via the SANTIS ADSL Router.

Features

ADSL Compliance

ANSI T1.413 Issue 2

ITU G.992.2 Annex A (G.lite)

ITU G.992.1 Annex A (G.dmt)

ITU G.992.1 Annex B (G.dmt)

ITU G.994.1 (G.hs)

Wireless LAN Features

Fully compatible to IEEE 802.11b standard and allow operating range up to 300 meters (open space) and 100
meters (indoor).

The Direct Sequence Spread Spectrum (DSSS) technology is exploited.

Seamless roaming within the 802.11 and 802.11b wireless LAN infrastructure

Low power consumption via efficient power management

Support the Association Control function: Only registered wireless clients can be allowed to associate to
wireless ADSL router.

ATM Features

Compliant to ATM Forum UNI 3.1 / 4.0 Permanent Virtual Circuits (PVCs)

Support up to 8 AAL5 Virtual Circuit Channels (VCCs) for UBR, CBR, VBR-rt, and VBR-nrt with traffic
shaping

TR-037 Auto PVC (auto-provisioning)

RFC1483 (RFC2684) LLC Encapsulation and VC Multiplexing over AAL5

RFC2364 Point-to-Point Protocol (PPP) over AAL5

RFC2225 Classical IP and ARP over ATM

RFC2516 PPP over Ethernet: support Relay (Transparent Forwarding) and Client functions

OAM F4/F5 End-to-End/Segment Loopback Cells

Bridging Features

Supports self-learning bridge specified in IEEE 802.1D Transparent Bridging

Supports up to 4000 learning MAC addresses

Transparent bridging among 10/100 Mb Ethernet and 802.11b Wireless LAN interfaces

Routing Features

UPnP IGD (Internet Gateway Device) with NAT traversal capability support

5

«
...
3
4
5
6
7
...
»

Summary of Contents for ADSL 500










































































Reviews:

No comments

Related manuals for ADSL 500

Brand: Idis Pages: 123

Brand: Idis Pages: 29

Brand: Idis Pages: 28

DirectIP DR-1304P

Brand: Idis Pages: 82

Brand: iDirect Pages: 130

Brand: M86 Security Pages: 46

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

Brand: TRENDnet Pages: 62

Brand: Patton electronics Pages: 13

Brand: Angel Cool Pages: 2

MMAC-Plus 9G536-04

Brand: Cabletron Systems Pages: 42

Slideaway CL1008

Brand: ATEN Pages: 77

Brand: ADTRAN Pages: 136

Brand: Netequalizer Pages: 14

Brand: Trend Micro Pages: 2

Brand: Juniper Pages: 30

Brand: ActionTec Pages: 87

Brand: JETWAY Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands