Siemens ADSL 500 User Manual Download Page 61 | Manualshive

Page: 61 / 73

background image

Chapter 4: Connection Mode

Bridge Mode

BRAS Broadband Remote Access Server

PPPoE
Client S/W

RADIUS

Server

PPP over Ethernet

Bridge

Mode

PC(s)

BRAS

STM-1

DSLAM

ADSL
Router

Loop

ISP

AAA

Default Private IP
192.168.1.1

Public IP assigned
by BRAS

Hub

Description:

In this example, the ADSL Router acts as a bridge which bridging PC IP address from LAN to WAN. PC IP address
can be a static public address that is pre-assigned by ISP or a dynamic public address that is assigned by ISP DHCP
server, or can be got from PPPoE software.

Therefore, it does not require a public IP address. It only has a default private IP address (192.168.1.1) for
management purpose.

Configuration:

1.

Choose a client PC and set the IP as 192.168.1.x (x is between 2 and 254) and the gateway as 192.168.1.1. Or
enter the IP address that came from the ISP DHCP server of the Router.

2.

Start up your browser and type

192.168.1.1

as the address to enter the web-based manager.

3. Go

to

Advanced User > Configuration >WAN Configuration > Create a New PVC

and select the Data

Mode –

RFC1483 Bridged

. Then click

Next

button.

4.

Enter the VPI/VCI values provided by your ISP and select the encapsulation type as

LLC/SNAP

or

VC MUX

.

Then click

Apply

.

5.

Save the configuration from

System

>

Save Configuration

and

System

>

Restart

to restart your router for

initiating these settings.

61

«
...
59
60
61
62
63
...
»

Summary of Contents for ADSL 500










































































Reviews:

No comments

Related manuals for ADSL 500

Device Server UDS 10

Brand: Lantronix Pages: 8

Azure StorSimple 8100

Brand: Microsoft Pages: 12

Brand: QNO Pages: 106

Brand: Face Pages: 8

Brand: Idis Pages: 31

Brand: Magnadyne Pages: 8

Brand: IBM Pages: 34

Brand: ZyXEL Communications Pages: 8

Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...

Brand: 3Com Pages: 12

Brand: ADTRAN Pages: 136

Brand: MAKER MADE Pages: 40

OmniSwitch 6624

Brand: Alcatel Pages: 546

Brand: Vivotek Pages: 185

WNR2000v2 - Wireless- N 300 Router

Brand: NETGEAR Pages: 144

BladeCenter 1/10 Gb Uplink Ethernet SwitchModule

Brand: IBM Pages: 58

ForeFront 2616RC

Brand: Patton electronics Pages: 80

Brand: MasterForce Pages: 12

Brand: ADTRAN Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands