Siemens ADSL 500 User Manual Download Page 38 | Manualshive

Page: 38 / 73

background image

SANTIS ADSL 50/500 User Manual

Save Configuration

This page allows you to save all current configuration settings to non-volatile memory. Please wait for several
seconds to complete this process.

Upgrade Software

The ADSL Router supports the upgrading by using HTTP. To transfer the firmware file, follow the steps below:

1.

Download and unzip the new software file from vendor.

2. In

the

File Name of Firmware

field, click

Browse

to locate the upgrade file.

3. Click

the

Upgrade

button.

After upgrading, the original configuration will still exist and not reset to the factory defaults.

Reset Router

This page allows you to restart your router for invoking new configuration. After restarting, you should wait for
several seconds to let the system come up. When restarting the system, your brower session will be disconnected.
Please wait until the device finish restarting.

Note:

If

Reset to factory default settings

is checked, the settings will return to factory defaults,

including the

Username

and

Password

.

38

«
...
36
37
38
39
40
...
»

Summary of Contents for ADSL 500










































































Reviews:

No comments

Related manuals for ADSL 500

Brand: Magnat Audio Pages: 2

Brand: TFortis Pages: 86

ZyXEL EES-1024AF

Brand: ZyXEL Communications Pages: 99

Brand: Grundig Pages: 24

Brand: Rosco Pages: 20

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 17

Monochrome Image Acquisition Device NI 1410

Brand: National Instruments Pages: 34

Brand: NetComm Pages: 34

Brand: IEI Technology Pages: 106

Brand: ZyXEL Communications Pages: 28

DSL906 1DA Series

Brand: Aztech Pages: 15

Brand: Cambium Networks Pages: 560

Brand: MikroTik Pages: 5

Schottky Barrier Diodes MA3XD21

Brand: Panasonic Pages: 3

Schottky Barrier Diodes MA2SE01

Brand: Panasonic Pages: 3

Schottky Barrier Diodes MA2SD32

Brand: Panasonic Pages: 3

Schottky Barrier Diodes MA2Z720

Brand: Panasonic Pages: 3

Schottky Barrier Diodes MA3X727 (MA727)

Brand: Panasonic Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands