Siemens ADSL 500 User Manual Download Page 68 | Manualshive

Page: 68 / 73

background image

SANTIS ADSL 50/500 User Manual

Request time out

Then the DNS is not reachable. Check your DNS setting on the ADSL Router.

Problems with Upgrading

The following lists the error messages that you may see during upgrading and the action to take.

Error Message

: invalid checksum

Possible

cause

: The firmware file to be used is damaged or the file format is wrong.

Action

: Make sure that your firmware file format is valid or get a new firmware file.

Error Message

: invalid hardcode

Possible cause

: The firmware file is not compatible with the model of your ADSL Router.

Action

: Download a compatible firmware from the web.

Error Message

: unknown flags type

Possible cause

: The firmware version is not compatible.

Action

: Download a compatible firmware from the web.

Error Message

: internal isfs error / internal flashfs error

Possible cause

: System error occurs. It may cause by the lack of memory.

Action

: Reboot your ADSL Router and perform the upgrade task again.

Error Message

: invalid file format

Possible cause

: The firmware file format is invalid.

Action

: Check the file format is correct, otherwise download a firmware file with correct format.

Error Message

: get an error message

Possible cause

: The TFTP server responses with error message.

Action

: Make sure the file name you enter is correct. Otherwise the TFTP server may response with the error

message “File not found”.

Error Message

: transfer time out

Possible cause

: The transfer session is interrupted.

Action

:

a. Make sure the TFTP server is on the same subnet with the ADSL Router.
b. Make sure you the IP address of the TFTP server you specify is correct and that your TFTP server is started.
c. If error still occurs, reboot your ADSL Router and perform the upgrade task again.

Error Message

: firmware update in process

Possible cause

: The upgrade is already in process.

Action

: Do not turn off your ADSL Router otherwise you will cause damage to the device.

Error Message

: no remote server IP

Possible cause

: The IP address of the TFTP server is not specified.

Action

: Specify the IP address of the TFTP server is not specified.

68

«
...
66
67
68
69
70
...
»

Summary of Contents for ADSL 500










































































Reviews:

No comments

Related manuals for ADSL 500

Brand: iDirect Pages: 60

Brand: Ubiquiti Pages: 3

ADSL 2/2+ Router with USB Port ADE-3410v2

Brand: Planet Pages: 62

Brand: Enginko Pages: 19

Brand: Matrix Switch Corporation Pages: 61

Brand: Nilox Pages: 66

Brand: National Instruments Pages: 80

Brand: Buffalo Pages: 2

Brand: Amphenol Pages: 43

ELITE LCD UPGRADE KIT

Brand: Corsair Pages: 11

SecPath F50X0 Series

Brand: H3C Pages: 41

Brand: TRENDnet Pages: 205

Cheetah EtherCard-2320

Brand: Accton Technology Pages: 10

Brand: C&H Technologies Pages: 2

Dimension GS-2024

Brand: ZyXEL Communications Pages: 266

Brand: Thecus Pages: 148

NetVanta 300 Series

Brand: ADTRAN Pages: 2

3C13755-US - Router 5642

Brand: 3Com Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands