Siemens 6ES7144-5KD50-0BA0 Manual Download Page 45

Page: 45 / 55

Technical specifications

6.1 Technical specifications

Analog input module AI 4xRTD/TC 4xM12 (6ES7144-5KD50-0BA0)

Equipment Manual, 08/2020, A5E48753535-AA

Article number

6ES7144-5KD50-0BA0

Interference voltage suppression for f = n x (f1

+/- 0.5 %), f1 = interference frequency

•

Series mode interference (peak value of

interference < rated value of input range),

min.

40 dB

Interrupts/diagnostics/status information

Alarms

•

Diagnostic alarm

Yes; Parameterizable

•

Limit value alarm

Yes; Parameterizable

Diagnostic messages

•

Wire-break

Yes; Not for ±80 mV

•

Overflow/underflow

Yes

Diagnostics indication LED

•

Channel status display

Yes; green LED

•

for module diagnostics

Yes; green/red LED

Potential separation

between the load voltages

Yes

Potential separation channels

•

between the channels

•

between the channels and backplane bus

Yes

•

between the channels and the power sup-

ply of the electronics

Isolation

Isolation tested with

707 V DC (type test)

Degree and class of protection

IP degree of protection

IP65/67

Standards, approvals, certificates

Suitable for applications according to AMS

2750

Yes; Declaration of Conformity, see online support

entry 109757262

Suitable for applications according to CQI-9

Yes; Based on AMS 2750 E

Ambient conditions

Ambient temperature during operation

•

min.

-30 °C

•

max.

55 °C

Connection method

Design of electrical connection for the inputs

and outputs

M12, 5-pole

Design of electrical connection for supply volt-

age

M8, 4-pole

ET-Connection

•

ET-Connection

M8, 4-pin, shielded

Summary of Contents for 6ES7144-5KD50-0BA0
























































Search results

Summary of Contents for 6ES7144-5KD50-0BA0

Reviews:

Related manuals for 6ES7144-5KD50-0BA0

Brands by name

Popular brands

Siemens 6ES7144-5KD50-0BA0, Manual

Search results

Summary of Contents for 6ES7144-5KD50-0BA0

Reviews:

Related manuals for 6ES7144-5KD50-0BA0

Brands by name

Popular brands