Siemens 6ES7144-5KD50-0BA0 Manual Download Page 29 | Manualshive

Page: 29 / 55

background image

Parameters/address space

4.3 Explanation of the parameters

Analog input module AI 4xRTD/TC 4xM12 (6ES7144-5KD50-0BA0)

28

Equipment Manual, 08/2020, A5E48753535-AA

Compensation

type

Explanation

Internal reference

junction

Properties

With this compensation type, the reference junction temperature is determined with an internal tem-

perature sensor that is integrated in the AI 4xRTD/TC 4xM12 electronic module.

Note: Take the reaction time to changes of the ambient temperature into account.

Principle of operation

The reference junction temperature is detected through an internal temperature sensor.

All channels of the AI 4xRTD/TC 4xM12 that you select for this type of compensation receive the same

reference junction temperature.

Wiring

Connect the thermocouples directly or with compensating lines to the AI 4xRTD/TC 4xM12.

No compensation

Properties

With this compensation type, the reference junction temperature of the thermocouples is measured

outside the AI 4xRTD/TC 4xM12 electronic module. You can, for example, connect a compensating box

to the thermocouple for this purpose.

Principle of operation

The temperature of the reference junction for this type of compensation is specified as 0 °C.

This can be achieved by using a compensating box. A separate compensating box is required for each

thermocouple.

Wiring

Connect the compensating box with theAI 4xRTD/TC 4xM12 with copper cables.

Note: Thermocouples of Type B do not require a compensating box up to a reference junction temper-

ature of 50 °C.

«
...
27
28
29
30
31
...
»

Summary of Contents for 6ES7144-5KD50-0BA0
























































Reviews:

No comments

Related manuals for 6ES7144-5KD50-0BA0

Brand: National Instruments Pages: 8

Brand: Panasonic Pages: 16

Brand: salmson Pages: 12

Brand: ICP DAS USA Pages: 4

Brand: National Instruments Pages: 21

Brand: National Instruments Pages: 10

Brand: Idemia Pages: 29

Brand: RainSoft Pages: 16

Brand: R. Beck Maschinenbau Pages: 34

Brand: Absima Pages: 5

Brand: FARFISA INTERCOMS Pages: 36

Brand: The Handy Pages: 4

Brand: FAIE Pages: 5

Brand: M-system Pages: 10

Brand: Carel Pages: 2

Brand: Roger Pages: 2

DRINKWORKS Home Bar Classic

Brand: Keurig Pages: 32

Brand: golmar Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands