Siemens 6ES7144-5KD50-0BA0 Manual Download Page 41

Page: 41 / 55

Analog input module AI 4xRTD/TC 4xM12 (6ES7144-5KD50-0BA0)

Equipment Manual, 08/2020, A5E48753535-AA

Technical specifications

6.1

Technical specifications

Technical specifications of the AI 4xRTD/TC 4xM12 analog input module

The following table shows the technical specifications as of 08/2020. You will find a data

sheet including daily updated technical specifications on the Internet

(

https://support.industry.siemens.com/cs/ww/en/pv/6ES7144-5KD50-0BA0/td?dl=en

Article number

6ES7144-5KD50-0BA0

General information

Product type designation

AI 4xRTD/TC

HW functional status

FS01

Firmware version

V1.0.x

Product function

•

I&M data

Yes; I&M0 to I&M3

Engineering with

•

STEP 7 TIA Portal configurable/integrated

from version

STEP 7 V16 or higher

•

STEP 7 configurable/integrated from ver-

sion

V5.5 SP4 and higher

•

PROFIBUS from GSD version/GSD revision

GSD as of Revision 5

•

PROFINET from GSD version/GSD revision

GSDML V2.34

Supply voltage

Load voltage 1L+

•

Rated value (DC)

24 V

•

permissible range, lower limit (DC)

20.4 V

•

permissible range, upper limit (DC)

28.8 V

•

Reverse polarity protection

Yes; against destruction

Input current

Current consumption (rated value)

25 mA; without load

from load voltage 1L+ (unswitched voltage)

4 A; Maximum value

from load voltage 2L+, max.

4 A; Maximum value

Power loss

Power loss, typ.

0.6 W

Summary of Contents for 6ES7144-5KD50-0BA0
























































Search results

Summary of Contents for 6ES7144-5KD50-0BA0

Reviews:

Related manuals for 6ES7144-5KD50-0BA0

Brands by name

Popular brands

Siemens 6ES7144-5KD50-0BA0, Manual

Search results

Summary of Contents for 6ES7144-5KD50-0BA0

Reviews:

Related manuals for 6ES7144-5KD50-0BA0

Brands by name

Popular brands