Siemens 3WX3641-7JR10, Operating Instructions Manual

Page: 25 / 36

25
Parameterizing values are examples
misc. I _on: here is set the operate value for load shedding. The
adjustable values are in the range of (50 % to 150 %) x Ir or "off".
The signal is only active after elapse of the delay time
set under menu option relay tx.
ZSS
misc.
I2td
misc.
I2tg
misc.
mem
misc.
U<
misc.
I_ab
misc.
I_an
misc.
=on/off
misc. ZSS
=on/off
misc. I2td
=on/off
misc. I2tg
=on/off
misc. mem
= 800 A
misc. I_ab
= 400 A
misc. I_an
EF
misc.
symU
misc.
U>
misc.
f<
misc.
f>
misc.
#on/off
misc. ZSS
#on/off
misc. I2td
#on/off
misc. I2tg
#on/off
misc. mem
#1000A
misc. I_ab
#500A
misc. I_an
?on/off
misc. ZSS
?on/off
misc. I2td
?on/off
misc. I2tg
?on/off
misc. mem
?1000A
misc. I_ab
?500A
misc. I_an
=on/off
misc. ZSS
=on/off
misc. I2td
=on/off
misc. I2tg
=on/off
misc. mem
=1000A
misc. I_ab
=500A
misc. I_an
misc.
protec.
value P
value f
value U
value I
menu
relay
status
=on/off
misc. mem
#on/off
misc. mem
?on/off
misc. mem
=on/off
misc. mem
mem
misc.
=on/off
misc. mem
#on/off
misc. mem
?on/off
misc. mem
=on/off
misc. mem
phasI
=on/off
misc. mem
#on/off
misc. mem
?on/off
misc. mem
=on/off
misc. mem
mem
misc.
=on/off
misc. mem
#on/off
misc. mem
?on/off
misc. mem
=on/off
misc. mem
symI
=off
misc. mem
#50%
misc. mem
?50%
misc. mem
=50%
misc. mem
*) not available
Menu misc.
In this menu option, setting of additional protective parameters is
carried out.
misc. ZSS: enabling and disabling of the short-time grading
control
misc. I 2 t
d
: enabling and disabling of the I 2 t = constant charac-
teristic of the short-time grading control
misc. I 2 t
d
: enabling and disabling of the I 2 t = constant charac-
ter of the earth-fault protection
misc. mem: enabling and disabling of the thermal memory
misc. phasl: enabling and disabling of the phase-failure sensi-
tivity
misc. syml: here, the operate value for permissible current
unbalance of the phases is determined. The adjust-
able values are 50 % or "off". If the menu option
relay opt is enabled, on occurrence of the
parameterized unbalance, the output "optional sig-
nal" is set and the circuit-breaker is tripped after
elapse of the delay time set under relay tx.
misc. symU: not available
misc. EF: not available
misc. f<: not available
misc. f>: not available
misc. U<: not available
misc. U>: not available
misc. I _off: here is set the operate value for load shedding. The
adjustable values are in the range of (20 % to 150 %) x lr or "off".
Caution
The signal is only active after elapse of the delay time
set under menu option relay tx.
If the signal "lead time overload trip pending" is to be
used, this parameter must be set to off.
misc.
protec.
value f value U
value I
menu
relay
status
status
Test
status
D-Nr.
status
L-Nr.
status
Bus
status
In
status Test
=System OK
status D-Nr
= 23456
status L-Nr
= 3
status Bus
= RS485
status In
= 1600 A
value P
Measure values are example
Menu status
In this menu option, status information is
displayed.
status D No., status L No.: not available
status bus:
higher-level communication bus
system (if present)
status ln: circuit-breaker rated current
The rated current value may only be changed
when the release is removed (disconnected)
from the circuit-breaker. The entered value
must be identical to the value of the rated
current on the rating plate of the circuit breaker.
Incorrect entry will cause false or delayed
tripping. After I
n
all protective parameters (I
n
,
I
d
, I
i
,...) should be checked.
status Test: result of the internal release test
misc.
protec.
value f
value U
value I
Menu
status
value P
g
relay
temp
relay
opt.
relay
tx
relay
= on/off
relay g
= on/off
relay temp
= on/off
relay opt.
= 10 s
relay tx
# on/off
relay g
# on/off
relay temp
#= on/off
relay opt.
# 15 s
relay tx
? on/off
relay g
? on/off
relay temp
? on/off
relay opt.
? 15 s
relay tx
= on/off
relay g
= on/off
relay temp
= on/off
relay opt.
= 15 s
relay tx
relay
Menu relay
relay g:
on - exceeding the operate value of the earth-fault protection
leads to trip
off - exceeding the operate value of the earth-fault protection
activates the earth-fault LED. Indication can only be reset
after the operate value has been undershot
This is possible only on overcurrent releases S and T.
relay temp:
on - exceeding the temperature limit in the release enclosure
activates the optional signal (the optional signal must be
enabled by the relay opt. menu option)
off - exceeding the temperature limit in the release enclosure
activates not signal
relay opt.
on - the optional signal is activated if at least one of the enabled
causes is present (Addition syml or relay temp)
off - optional signal is disabled
relay tx:
Delay time for menu options: Addition
I
_off, Addition
I
_on.
Parameterizing values are examples
*
*
* *
*