Siemens 3VA1 100 A Manual Download

Page: 417 / 532

Accessories

4.14 DIN rail adapter

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

417

Information about combination with other accessories

DIN rail adapters are normally used to install molded case circuit breakers (possibly with side

mounted residual current device) in distribution boards. The standard cover is then fitted

over the circuit breakers. The front panel (45 mm high) is the only part of the device which

protrudes through the cover. With this arrangement, it is not possible to use front mounted

accessories.
When molded case circuit breakers including DIN rail adapter are installed on rails in an

open system cubicle without a cover, it is possible to use front mounted accessories such as

motor operator, rotary operator with shaft stub, front mounted rotary operator and the front

mounted Bowden cable interlock module.
The following accessories are compatible with molded case circuit breakers and DIN rail

adapters:

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands