Siemens 3VA1 100 A Manual Download Page 355

Page: 355 / 532

Accessories

4.8 Residual current devices

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

355

4.8.3

Modular residual current device

Thanks to its design, the modular residual current device type A (MRCD) 5SV8101-6KK is

compatible with all molded case circuit breaker designs and can therefore be combined with

3VA1 molded case circuit breakers/switch disconnectors and with molded case circuit

breakers from the 3VA2 series.
The modular residual current device is installed on a DIN rail (35 mm) as close as possible to

the molded case circuit breaker/switch disconnector.

Operating principle
The modular residual current device is connected to a summation current transformer

through which all live conductors (including neutral conductor where applicable) must be

routed. The residual current is detected in the summation current transformer and

transferred to the MRCD. If this current exceeds the limit value for the set rated residual

current I

Δn

, the residual current device trips the molded case circuit breaker/switch

disconnector by means of a shunt trip or undervoltage release.

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Brands by name

Popular brands