Siemens 3VA1 100 A Manual Download | Manualshive

Page: 407 / 532

background image

Accessories

4.11 Test devices

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

407

Test transformers

This procedure tests the transformers (energy transformer or Rogowski coil) to determine the

following:

●

Are transformers installed in the ETU?

●

Are transformers correctly installed in the ETU?

●

Are the installed transformers functioning correctly?

Note
In order to carry out this test, it is absolutely essential to disconnect all external power

supplies (e.g. EFB300, COM800, COM100, 24 V module) to the electronics.

Execute the test
1.

Disconnect all external power supplies to the electronics.

2.

Connect the TD500 test device to the 3VA2 molded case circuit breaker.

3.

Switch on the 3VA2 molded case circuit breaker.

4.

Press the pushbutton labeled <TRANS>

①

.

The LED in the <TRANS> pushbutton begins to flash. The test takes several seconds.

5.

Wait until the LED in the pushbutton <TRANS> changes from flashing to steady

illumination.

The test is completed.

6.

Evaluate the test result by the status of the LED labeled "RESULT":
LED "RESULT" is illuminated steadily in green: The test was successful.
LED "RESULT" flashes red: The test was unsuccessful and must be repeated. If the test

fails again, contact Technical Support (Page 12) .

7.

Press the pushbutton <TRANS> again in order to confirm the test result and restore the

TD500 to its initial state.

«
...
405
406
407
408
409
...
»

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3VA1 100 A

NZM1-XHB-DA-OAG

Brand: Eaton Pages: 3

Brand: Moeller Pages: 2

Brand: Moeller Pages: 3

Brand: Moeller Pages: 42

Brand: Bticino Pages: 4

Brand: Bticino Pages: 4

Brand: nader Pages: 39

Brand: Noark Pages: 55

Brand: ABB Pages: 17

Allen-Bradley 140M-C-TRE

Brand: Rockwell Automation Pages: 2

Allen-Bradley 140G-G

Brand: Rockwell Automation Pages: 3

1492-GS1 Series

Brand: Rockwell Automation Pages: 2

Allen-Bradley 140U

Brand: Rockwell Automation Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands