Siemens 3VA1 100 A Manual Download

Page: 198 / 532

Accessories

4.3 Connection system

3VA molded case circuit breakers

198

Manual, 04/2015, A5E03603177010-02

Touch protection

Insulated cables and busbars
With insulated cables and busbars that have insulation that reaches inside the terminal

compartment of the 3VA molded case circuit breaker, the unit is classed as finger-safe

(IP2X) if it is also equipped with a terminal cover. This protection is guaranteed only if the

unit is installed and wired correctly.

Non-insulated cables and busbars
With non-insulated cables and busbars, and front connection bars extended or front

connection bars broadened, the unit is classed as finger-safe (IP2X) if it is also equipped

with an extended or broadened terminal cover. This protection is guaranteed only if the unit

is installed and wired correctly.

External circular conductor terminals
External circular conductor terminals are supplied as standard with an extended terminal

cover. The external circular conductor terminals are classed as finger-safe (IP2X) on

condition that the extended terminal cover is correctly installed.

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands