Side-Power SEP 80/185 T Installation & User Manual Download

Page: 2 / 32

SRV(P)80/185T - SRL(P)80/185T - SRV(P)100/185T

SRL(P)100/185T

1.0.5 - Sept. 2014

Innhold

SamSvarS erklæring

Sleipner motor aS

Postboks 519

n-1612 Fredrikstad, norge

erklærer at dette produktet med tilhørende

standard kontrollsystemer er i samsvar med

helse, og sikkerhetskravene i henhold til Direk-

tiv 89/336/eeC Fra 23 mai 89, korrigert av

92/31/eeC og 93/68/eeC.

Installation instructions

Measurements, thruster..............................................................3

Planning and important precautions ...........................................4

Technical specifications

..............................................................5

Thruster installation

Positioning the thruster ..............................................................6

Moulding .....................................................................................9

Fitting upper part and hatch .................................................... 10

Fitting the electromotor ............................................................11

Electrical installation .................................................................12

Technical & visual wiring diagrams, SRV/SRL models .............13

Technical & visual wiring diagrams, SRVP/SRLP models ........14

Check and calibrate drive shaft alignment................................15

Maintenance .............................................................................16

S-Link

S-link system overview .............................................................17

Planning & precautions ............................................................18

User’s manual

Control panels ..........................................................................19

General use ............................................................................20

Installation checklist................................................................. 21

Important user precautions ...................................................... 22

Troubleshooting ....................................................................... 23

Warranty statement

.............................................................. 25

Spareparts lists & drawings

................................................ 26

Revision ....................................................................................28

Service centres

..................................................................... 32

Contents

DeClaraTiOn OF COnFOrmiTY

We,

Sleipner motor aS

P.O. Box 519

n-1612 Fredrikstad, norway

declare that this product with accompanying

standard remote control systems complies with

the essential health and safety requirements

according to the Directive 89/336/eeC of 23

may 1989 amended by 92/31/eeC and

93/68/eeC.

Installasjonsinstrukser

Målskisse, truster........................................................................3

Planlegging og viktige brukerforbehold ......................................4

Tekniske spesifikasjoner

.............................................................5

Trusterinstallasjon

Plassering av enheten ...............................................................6

Laminering ..................................................................................9

Montering av overdel og luke .................................................. 10

Montering av elektromotor .......................................................11

Elektrisk installasjon

.................................................................12

Technical & visual wiring diagrams, SRV/SRL models .............13

Technical & visual wiring diagrams, SRVP/SRLP models ........14

Kontroll og kalibrering av drivakselposisjon

..............................15

Vedlikehold ...............................................................................16

S-link

Systemoversikt .........................................................................17

Planlegging og forbehold .........................................................18

Brukermanual

Kontollpanel .............................................................................19

Generell bruk ............................................................................20

Sjekkliste

................................................................................. 21

Viktige brukerforbehold ............................................................ 22

Problemer og løsninger ........................................................... 23

Warranty statement

.............................................................. 25

Delelister/tegninger

.............................................................. 26

Revisjon

....................................................................................28

Servicesentre

........................................................................ 32

Summary of Contents for SEP 80/185 T

































Search results

Summary of Contents for SEP 80/185 T

Reviews:

Related manuals for SEP 80/185 T

Brands by name

Popular brands

Side-Power SEP 80/185 T, Installation & User Manual

Search results

Summary of Contents for SEP 80/185 T

Reviews:

Related manuals for SEP 80/185 T

Brands by name

Popular brands