11
Setting High and Low Limits
If the variation of motor speed or time measurement is important and a “range” must be monitored, then “high” and
“low” visual limits can be programmed through secondary displays A and B, respectively.
Instructions to set the high and low limits:
1. Use the lower buttons (1-6) to set the high limit on secondary display A. There are six digits that can be
programmed and each one of these buttons corresponds with the digit position. Each time one of the buttons
is pressed, the display will increment that position one number (for example, if 56000 RPM needs to be programmed
as the high limit, then NUMERIC button 2 would have to be pressed five times and NUMERIC button 3 would be
pressed six times).
2. Use the lower buttons (7 - BACKSPACE) to set the low limit on secondary display B. These six buttons also
correspond with the digit positions and will increment that position one number (for example, if 3425 RPM needs
to be programmed as the low limit, then NUMERIC button 9 should be pressed three times, NUMERIC button 0
pressed four times, NEGATIVE/DECIMAL button pressed twice and the BACKSPACE button pressed five times).
3. Press the SET button to store the limit settings.
The comparator indicators will illuminate when the primary display exceeds the high set point (
∆
) or the low set
point (
∇
).
NOTE: The DT-5TXR provides relay or transistor closures (see section “Modules Available for DT-5TXR” on page 15).
Setting Functions
The DT-5TXR/DT-5TS has a variety of functions that can be programmed to further customize the meter. Listed below
are the available functions:
MODE -01-
MODE -03-
NOTE: Although the functions are rarely used in mode -03-, they are still available.
MODE -02-
DISPLAY
MEANING
1
The 2nd high and the 2nd low limit setting
000000 - 999999
0 0 0 0 0 0
0
9
9
-
0
g
ni
tt
e
s
w
o
l
t
s
1
d
n
a
h
g
i
h
t
s
1
f
o
si
s
e
r
e
t
s
y
H
2
_ _ _ _
0 0
0
3
Secures the 1st high and 1st low setting
0 (not secured )/1 (secured)
_
0
_
Not secured
d
n
o
c
e
s
9
9
-
0
ti
m
il
t
e
s
y
n
a
f
o
n
o
it
a
v
it
c
a
t
u
p
t
u
O
4
_ _ _ _
0 0
0 second
5
Selection of secondary display
0 (1st high and 1st low limit set) 1(blank)/2 (real RPM)
_
0
_
1st high and 1st low limit set
6
Main display shows 0 below this no. setting
000000 - 999999
0 0 0 0 0 0
0
7
Averages the sensor output frequency
0 (none)/1 (three times)/2 (ten times)
_
0
_
None
)
n
o
(
1
/)
f
f
o
(
0
e
u
l
a
v
y
a
lp
s
i
d
O
R
E
Z
o
t
n
o
it
a
r
e
le
c
e
D
8
_
0
_
Off
FACTORY SETTING
RANGE
DESCRIPTION
FUNCTION
DISPLAY
MEANING
1
The 2nd high and the 2nd low limit setting
0:00:00 - 9:59:59 or 0:00 – 999.99
_
0 0 0 0 0
1/100 second
9
9
-
0
t
e
s
w
o
l
t
s
1
d
n
a
h
g
i
h
t
s
1
f
o
si
s
e
r
e
t
s
y
H
2
_ _ _ _
0 0
0
3
Secures the 1st high and 1st low set
0 (Not secured )/1 (Secured)
_
0
_
Not secured
d
n
o
c
e
s
9
9
-
0
ti
m
il
t
e
s
y
n
a
f
o
n
o
it
a
v
it
c
a
t
u
p
t
u
O
4
_ _ _ _
0 0
0 second
5
Selection of secondary display
0 (1st high and 1st low limit set)/1 (blank)/2 (real RPM)
_
0
_
1st high and 1st low limit set
6
Main display shows 0 below this no. setting
000000 - 999999
0 0 0 0 0 0
0
7
Averages the sensor output frequency
0 (none)/1 (three times)/2 (ten times)
_
0
_
None
)
n
o
(
1
/)
f
f
o
(
0
e
u
la
v
y
al
p
si
d
O
R
E
Z
o
t
n
o
it
a
r
el
e
c
e
D
8
_
0
_
Off
FACTORY SETTING
FUNCTION
DESCRIPTION
E
G
N
A
R
DISPLAY
MEANING
1
The 2nd high and the 2 nd low limit setting
0:00:00 - 9:59:59 or 0:0 0 - 999.99
_
0 0 0 0 0
1/100 second
2
Hysteresis of 1st high and 1st low setting
0 - 99
_ _ _ _
0 0
0
3
Secure the 1st high and 1st low setting
0 (not secured )/1 (secured)
_
0
_
Not secured
d
n
o
c
e
s
9
9
-
0
ti
m
il
t
e
s
y
n
a
f
o
n
o
it
a
v
it
c
a
t
u
p
t
u
O
4
_ _ _ _
0 0
0 second
5
Selection of secondary display
0 (1st high and 1st low limit set)/1 (blank)/2 (real RPM)
_
0
_
1st high and 1st low limit setting
FUNCTION
DESCRIPTION
E
G
N
A
R
FACTORY SETTING
www.
GlobalTestSupply
.com
Find Quality Products Online at:
