SHIFT4 UTG Ingenico 3070 Manual Download Page 44

Page: 44 / 64

Universal Transaction Gateway

Using Legacy External Devices

Version 1.4

External Use NDA

Page 44 of 64

Other Settings

Verify that the following settings have been applied on the UTG Stub IP to Serial window:

•

Data Bits (Byte Size): 7

•

Parity: Even

•

Stop Bits: 1

•

Flow Control: None

Configuring the Verifone PINpad 1000 Series

The UTG supports two devices in the Verifone PINpad 1000 series, as shown below. The Verifone

PINpad 1000 (shown on the left) has 10 number buttons, a red Clear button, and blue Enter button. The

Verifone

PINpad 1000se (shown on the right) also has 10 number buttons, in addition to three blue

function keys, a red

“

”

(cancel) button, a green arrow (enter) button, and a yellow arrow (clear) button.

Verifone PINpad 1000

Verifone PINpad 1000se

Resetting the Device

To reset the Verifone PINpad 1000 or Verifone PINpad 1000se, complete the following steps:
102.

Disconnect and reconnect the power cord.

103.

While holding down the

CLEAR

button, press

104.

When prompted for the password, type

844747746

105.

Press

ENTER

Setting the Baud Rate

106.

On the scrolling message, watch for the number to press to open the Baud Rate menu.

107.

Press the appropriate number for the Baud Rate menu.

Summary of Contents for UTG Ingenico 3070































































Search results

Summary of Contents for UTG Ingenico 3070

Reviews:

Related manuals for UTG Ingenico 3070

Brands by name

Popular brands

SHIFT4 UTG Ingenico 3070, Manual

Search results

Summary of Contents for UTG Ingenico 3070

Reviews:

Related manuals for UTG Ingenico 3070

Brands by name

Popular brands