Appendix
102
Symptom
Tape stops during rewind or fast
forward.
No image appears on connected
TV screen.
Cannot play back, rewind or fast
forward tape.
Video noise in image.
Cannot delete image on
SmartMedia card.
Cannot format SmartMedia card.
Cassette will not eject.
Viewfinder picture is hard to
see.
LCD monitor picture is hard to
see.
Cannot edit to connected video
equipment.
Infrared remote control does not
function.
Possible cause
Counter memory is on.
Video input channel on TV or TV channel is not
selected properly.
Audio/video/S-video cable is not properly
connected.
Position at beginning or end of tape.
Dirty video heads.
Old or worn tape.
Write-protect seal is affixed to card.
Image is delete-protected.
Write-protect seal is affixed to card.
Power source is not properly connected.
Battery pack is not charged.
Camcorder is recording.
Viewfinder dioptre is not properly adjusted.
Inappropriate picture adjustments.
Audio/video/S-video or DV cable is not properly
connected.
REMOTE menu item is set to “OFF”.
Remote control lithium battery has run down.
Remote control used beyond operating range.
Intense daylight falling on camcorder remote
sensor.
Obstacle between remote control and camcorder
remote sensor.
Suggested solution
Turn off counter memory (
p. 47
).
Select video input channel or TV channel
properly (
p. 23
).
Connect audio/video/S-video cable properly
(
p. 23
).
Rewind or fast forward tape to desired point
(
p. 22
).
Call for service (
p. 101
), or use a
commercially-available video head cleaning tape
(
p. 99
).
Use a new cassette.
Remove write-protect seal (
p. 96
).
Cancel the protection setting (
p. 80
).
Remove write-protect seal (
p. 96
).
Connect power source properly (
pp. 10, 11
).
Charge battery pack sufficiently (
p. 9
).
Stop tape and try again (
p. 19
).
Adjust dioptre (
p. 17
).
Adjust picture (
p. 64
).
Connect audio/video/S-video or DV cable
properly (
pp. 65, 66
).
Set REMOTE menu item to “ON” (
p. 40
).
Replace remote control lithium battery with a
new one (
p. 14
).
Use remote control within operating range
(
p. 40
).
Protect remote sensor from exposure to intense
daylight (
p. 40
).
Remove obstacle or use remote control from
different angle (
p. 40
).
General
Card mode
Playback mode
Notes:
• This unit is equipped with a microprocessor. Its performance could be adversely affected by external electrical
noise or interference. If this should happen, turn off the power and disconnect the unit from any power sources,
including the lithium battery, etc. Then reconnect the power sources to resume operation.
• If the characters displayed in the viewfinder or on the LCD monitor appear to malfunction, disconnect the
power source and remove the lithium battery, then reconnect the power source, insert the lithium battery, and
turn the power on again. The characters should be normal. Set the date and time, then resume operation.
VL-PD6H/093-103
01.4.24, 0:45 PM
102
http://www.usersmanualguide.com/
Summary of Contents for VL-PD6H Quick operation
Page 113: ...Memo VL PD6H memo1 3 01 4 24 11 59 AM 1 Downloaded from http www usersmanualguide com ...
Page 114: ...Memo VL PD6H memo1 3 01 4 24 11 59 AM 2 Downloaded from http www usersmanualguide com ...
Page 115: ...VL PD6H memo1 3 01 4 24 11 59 AM 3 Downloaded from http www usersmanualguide com ...
