MX-M260/M310/M260N/M310N SIMULATION 6 - 21
Operation/procedure
Operation/procedure
Select the short time setup or the long time setup of the pre-heat time
and the auto power shut off time with the 10-key, and press the
[START] key.
Note: When the sub code 71 is entered to display the setting menu,the
default values are always displayed. (However,the default time is
not always set.)
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Operation/procedure
Input the set value with the 10-key and press the [START] key.
Operation/procedure
1.
The current setting value is displayed in PRESENT field.
2.
Enter the number with 10-key, the setting value is saved and the
display of PRESENT is updated.
Operation/procedure
Enter the item number of setting with 10-key, press [START] key.
26-69
Purpose
Setting
Function (Purpose)
Toner near end setting
Item
Operation
Item
Set value
Default
1
Toner preparation
message display
setting.
0: Displayed
1: Not displayed
0
2
Toner near end
massage display
setting.
0: Displayed
1: Not displayed
0
3
Toner end status
operation setting.
1: Operate
2: Operate (However, if
CRUM ID matches, not
operates.)
3: Not operate
3
4
E-mail alert sending
timing setting.
0: When the near near
toner end, the toner low
status is sent.
1: When the near toner
end, the toner low
status is sent.
1
26-71
Purpose
Setting
Function
(Purpose)
In the power save time setting, the pre-heat (pre-heat
mode setting) and the auto power shut off time can be
set to the short time setup (pre-heat: 1 min, auto power
shut off: 4 min) and the long time setup (pre-heat:
5min, auto power shut off: 30min).
Item
Content
Default
1
Preheat: 1min, auto power shut off: 4min
2
2
Preheat: 5min, auto power shut off: 30min
26-72
Purpose
Setting
Function
(Purpose)
The letterhead support is set.
When “Letterhead paper setting” is selected, the set
value of SIM 26-46 (Image output direction setting) is
set to “Setting Enable” accordingly.
Item
Content
Setting
range
Default
0
OFF
Letterhead paper is not set.
0-1
0
1
ON
Letterhead paper is set.
27
27-1
Purpose
Setting
Function
(Purpose)
Used to set PC/MODEM communication trouble
(U7-00) detection Yes/No.
Section
Communication (RIC/MODEM)
Item
Specifications
Operation mode (Common)
Item
Content
Default
0
OFF
In case of the communication trouble, U7-00 is
not displayed.
0
1
ON
In case of the communication trouble, U7-00 is
displayed.
27-2
Purpose
Setting
Function (Purpose)
Sender’s registration number/HOST server
TEL number.
27-4
Purpose
Setting
Function (Purpose)
Function setting
Display
Contents
Setting
range
Default
1
RETRY
BUSY
Recall number setting when
busy (unit: times)
0-5
2
2
TIMER
(MINUTES)
BUSY
Recall interval setting when
busy (unit:minute)
1-15
3
3
RETRY
ERROR
Recall number setting when
send error (unit: times)
0-15
1
4
TIMER
(MINUTES)
ERROR
Recall interval setting when
send error (unit: minute)
1-15
1
5
TONER
ORDER
TIMING
Toner order
auto send
timing setting
Empty
0-5
0
3
Near End
1
25% or less
2
25-49%
3
50-74%
4
75-100%
5
6
FAX INIT
RETRY
Retry number setting of initial
connection (unit: times)
0-15
2