Sharp MX-M1054 Technical Handy Manual Download Page 7

Page: 7 / 76

Consumables

SHARP

Document Solution Centre

Machine Options

MX-M904 – MX-M1204

Model

Description

Comment

MX-GB50A

GBC Smart Punch Unit (A4)

MX-RB13 must follow unit

MX-GBX21

Plastic Comb (21 holes, rectangular A4)

MX-GBX20

Plastic Comb (20 holes, rectangular A4)

MX-GBX47

Colour Coil (47 holes, round, A4)

MX-GBX23

Wire 2:1 (23 holes, round, A4)

MX-GBX34

Wire 3:1 (34 holes, round, A4)

MX-GBX12

VeloBind (12 holes, round, A4)

MX-GBX34PR

ProClick (34 holes, rectangular, A4)

MX-GBX2H80

2 Hole (round, 8mm pin, A4)

MX-GBX4H80

4 Hole (round, 8mm pin, A4)

MX-GBX2H65

2 Hole (round, 6.5mm pin, A4)

MX-GBX4H65

4 Hole (round, 6.5mm pin, A4)

MX-GB54

Plastic Comb (DuraGlide HD, 21 holes, rectangular,

A4)

MX-GB55

Wire 3:1 (DuraGlide HD, 34 holes, round, A4)

MX-GB56

4 Hole (DuraGlide HD, 4 holes, round, 8mm pin, A4)

MX-BM50

Plockmatic Booklet Maker

Must be connected to the MF-

FN21.

MX-TM50

Trimmer Unit

MX-FD50

Square Fold Unit

MX-CF50

Cover Feeder Unit

MX-XB50

Rail Unit

Must be installed with MX-

BM50

MX-BM50 Plockmatic Booklet Maker

Summary of Contents for MX-M1054













































































Search results

Summary of Contents for MX-M1054

Reviews:

Sharp MX-M1054, Technical Handy Manual, Page: 7 / 76

Search results

Summary of Contents for MX-M1054

Reviews: